اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدTheoretical Modeling of ME effect at Low frequency and Resonance Frequency for Magnetoelectric Laminates with Anisotropic Piezoelectric Properties
41
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
A new theory is developed for the magnetoelectric (ME) coupling in a symmetric 2-2 ME laminate having a representative piezoelectric crystal (PMN-PT) particularly with anisotropic piezoelectric properties. Considering the average field method, the theoretical expressions for the transverse ME voltage coefficients at low and resonance frequencies were derived. The theory takes into account the anisotropic properties of the piezoelectric materials providing two different expressions of transverse ME voltage coefficients for different in-plane magnetic fields both at low and resonance frequencies. The numerical simulations show multiple resonance frequencies and phase differences between transverse ME voltage coefficients showing good agreement with the experimental results. Our theory should be generally applicable to other ME laminates with any piezoelectric with anisotropic piezoelectric coefficients.
قيم البحث
اقرأ أيضاً
We report the experimental observation in thin films of the hybridization of the uniform ferromagnetic resonance mode with nonuniform magnons as a result of the two-magnon scattering mechanism, leading to a frequency-pulling effect on the ferromagnet
ic resonance. This effect, when not properly accounted for, leads to a discrepancy in the dependence of the ferromagnetic resonance field on frequency for different field orientations. The frequency-pulling effect is the complement of the broadening of the ferromagnetic resonance lineshape by two-magnon scattering and can be calculated using the same parameters. By accounting for the two-magnon frequency shifts through these means, consistency is achieved in fitting data from in-plane and perpendicular-to-plane resonance conditions.
In contrast to the Pb-based magnetoelectric laminates (MELs), we find in the BaTiO3 and NiFe2O4 laminates (number of layers n = 5-25) that the longitudinal magnetoelectric (ME) voltage coefficient Alpha E33 becomes much larger than the transverse one
due to preferential alignment of magnetic moments along the NiFe2O4 plane. Moreover, upon decreasing each layer thickness down to 15 um, we realize enhanced Alpha E33 up to 18 mV/ (cm Oe) and systematic increase of the ME sensitivity in proportion to n to achieve the largest in the Pb-free MELs (400*10^-6V/Oe), thereby providing pathways for tailoring ME coupling in mass-produced, environment friendly laminates.
We have investigated the low-frequency 1/f noise of both suspended and on-substrate graphene field-effect transistors and its dependence on gate voltage, in the temperature range between 300K and 30K. We have found that the noise amplitude away from
the Dirac point can be described by a generalized Hooges relation in which the Hooge parameter {alpha}H is not constant but decreases monotonically with the devices mobility, with a universal dependence that is sample and temperature independent. The value of {alpha}H is also affected by the dynamics of disorder, which is not reflected in the DC transport characteristics and varies with sample and temperature. We attribute the diverse behavior of gate voltage dependence of the noise amplitude to the relative contributions from various scattering mechanisms, and to potential fluctuations near the Dirac point caused by charge carrier inhomogeneity. The higher carrier mobility of suspended graphene devices accounts for values of 1/f noise significantly lower than those observed in on-substrate graphene devices and most traditional electronic materials.
The observation of strong magnetoelectric effects is reported in thick film bilayers and multilayers of ferrite-lead titanate zirconate (PZT) and lanthanum nanganite-PZT. The ferrites used in our studies included pure and zinc substituted cobalt-, ni
ckel- and lithium ferrites. Samples were prepared by sintering 10-40 mm thick films obtained by tape-casting. Measurements of ME voltage coefficients at 10-1000 Hz indicated a giant ME effect in nickel ferrite-PZT, but a relatively weak coupling in other ferrite-PZT and manganite-PZT systems. Multilayers prepared by hot pressing was found to show a higher ME coefficient than sintered samples. Evidence was found for enhancement in ME coefficients when Zn was substituted in ferrites. The Zn-assisted increase was attributed to low anisotropy and high permeability that resulted in favorable magneto-mechanical coupling in the composites. We analyzed the data in terms of our recent comprehensive theory that takes into account actual interface conditions by introducing an interface coupling parameter. Theoretical longitudinal and transverse ME voltage coefficients for unclamped and clamped samples are in general agreement with data. From the analysis we inferred excellent interface coupling for nickel zinc ferrite-PZT and weak coupling for other layered systems.
We present a study of resonant vibrational coupling between adsorbates and an elastic substrate at low macroscopic coverages. In the first part of the paper we consider the situation when adsorbates form aggregates with high local coverage. Based upo
n our previously published theory, we derive formulas describing the damping rate of adsorbate vibrations for two cases of such aggregation: (i) adsorbates attached to step edges and (ii) adsorbates forming two-dimensional islands. We have shown that damping is governed by local coverage. Particularly, for a wide range of resonant frequencies, the damping rate of adsorbates forming well separated islands is described by the damping rate formula for a periodic overlayer with the coverage equal to the local coverage in the island. The second part of the paper is devoted to facilitating the evaluation of damping rates for a disordered overlayer. The formula describing the damping rate involves the parameter $beta$ which is related to the local density of phonon states at the substrate surface and does not allow a closed-form representation. For substrates of isotropic and cubic symmetries, we have developed a good analytical approximation to this parameter. For a vast majority of cubic substrates the difference between the analytical approximation and numerical calculation does not exceed 4%.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
