اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدOptically optimal wavelength-scale patterned ITO/ZnO composite coatings for thin film solar cells
86
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
A methodology is proposed for finding structures that are, optically speaking, locally optimal : a physical analysis of much simpler structures is used to constrain the optimization process. The obtained designs are based on a flat amorphous silicon layer (to minimize recombination) with a patterned anti-reflective coating made of ITO or ZnO, or a composite ITO/ZnO coating. These latter structures are realistic and present good performances despite very thin active layers.
قيم البحث
اقرأ أيضاً
We study polarization independent improved light trapping in commercial thin film hydrogenated amorphous silicon (a-Si:H) solar photovoltaic cells using a three-dimensional silver array of multi-resonant nano-disk structures embedded in a silicon nit
ride anti-reflection coating (ARC) to enhance optical absorption in the intrinsic layer (i-a-Si:H) for the visible spectrum for any polarization angle. Predicted total optical enhancement (OE) in absorption in the i-a-Si:H for AM-1.5 solar spectrum is 18.51% as compared to the reference, and producing a 19.65% improvement in short-circuit current density (JSC) over 11.7 mA/cm2 for a reference cell. The JSC in the nano-disk patterned solar cell (NDPSC) was found to be higher than the commercial reference structure for any incident angle. The NDPSC has a multi-resonant optical response for the visible spectrum and the associated mechanism for OE in i-a-Si:H layer is excitation of Fabry-Perot resonance facilitated by surface plasmon resonances. The detrimental Staebler-Wronski effect (SWE) in a-Si:H solar cell can be minimized by the additional OE in the NDPSC and self-annealing of defect states by additional heat generation, thus likely improving the overall stabilized characteristics of a-Si:H solar cells.
In terms of mixing graded TiO2 and SnO2 powders by solid-state reaction method, ITO was prepared. Using electron beam gun technology, ITO films with different thicknesses were prepared. The influence of film thickness on structure, electrical and opt
ical properties was studied. The XRD patterns were utilized to determine the structural parameters (lattice strain and crystallite size) of ITO with different thicknesses. It is observed that the average crystallite size increases as the film thickness increases, but the lattice strain decreases. SEM shows that as the film thickness increases, the grain size of ITO increases and improves. The electrical properties of ITO films with different thicknesses were measured by the standard four-point probe method. It can be seen that as the thickness of the ITO film increases from 75 nm to 325 nm, the resistivity decreases from 29x10^-4 Ohm/cm to 1.65x10^-4 Ohm/cm. This means that ITO films with lower electrical properties will be more suitable for high-efficiency CdTe solar cells. Three optical layer models (adhesive layer of the substrate/B-spline layer of ITO film/surface roughness layer) are used to calculate the film thickness with high-precision ellipsometry. In the higher T(lambda) and R(lambda) absorption regions, the absorption coefficient is determined to calculate the optical energy gap, which increases from 3.56 eV to 3.69 eV. Finally, the effects of ITO layers of various thicknesses on the performance of CdS/CdTe solar cells are also studied. When the thickness of the ITO window layer is 325 nm, Voc = 0.82 V, Jsc = 17 mA/cm2, and FF = 57.4%, the highest power conversion efficiency (PCE) is 8.6%.
Strong interference in ultrathin film semiconductor absorbers on metallic back reflectors has been shown to enhance the light harvesting efficiency of solar cell materials. However, metallic back reflectors are not suitable for tandem cell configurat
ions because photons cannot be transmitted through the device. Here, we introduce a method to implement strong interference in ultrathin film top absorbers in a tandem cell configuration through use of distributed Bragg reflectors (DBRs). We showcase this by designing and fabricating a photoelectrochemical-photovoltaic (PEC-PV) stacked tandem cell in a V-shaped configuration where short wavelength photons are reflected back to the photoanode material (hematite, Fe2O3), whereas long wavelength photons are transmitted to the bottom silicon PV cell. We employ optical simulations to determine the optimal thicknesses of the DBR layers and the V-shape angle to maximize light absorption in the ultrathin (10 nm thick) hematite film. The DBR spectral response can be tailored to allow for a more than threefold enhancement in absorbed photons compared to a layer of the same thickness on transparent current collectors. Using a DBR to couple a bottom silicon PV cell with an ultrathin hematite top PEC cell, we demonstrate unassisted solar water splitting and show that DBRs can be designed to enhance strong interference in ultrathin films while enabling stacked tandem cell configuration.
An optoelectronic optimization was carried out for an AlGaAs solar cell containing (i) an n-AlGaAs absorber layer with a graded bandgap and (ii) a periodically corrugated Ag backreflector combined with localized ohmic Pd-Ge-Au backcontacts. The bandg
ap of the absorber layer was varied either sinusoidally or linearly. An efficiency of 33.1% with the 2000-nm-thick n-AlGaAs absorber layer is predicted with linearly graded bandgap along with silver backreflector and localized ohmic backcontacts, in comparison to 27.4% efficiency obtained with homogeneous bandgap and a continuous ohmic backcontact. Sinusoidal grading of the bandgap {is predicted to enhance} the maximum efficiency to 34.5%. Thus, grading the bandgap of the absorber layer, along with a periodically corrugated Ag backreflector and localized ohmic Pd-Ge-Au backcontacts can help realize ultrathin and high-efficient AlGaAs solar cells for terrestrial applications.
We report on very high enhancement of thin layers absorption through band-engineering of a photonic crystal structure. We realized amorphous silicon (aSi) photonic crystals, where slow light modes improve absorption efficiency. We show through simula
tion that an increase of the absorption by a factor of 1.5 is expected for a film of aSi. The proposal is then validated by an experimental demonstration, showing an important increase of the absorption of a layer of aSi over a spectral range of 0.32-0.76 microns.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
