اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCopper Planar Microcoils Applied to Magnetic Actuation
114
0
0.0
(
0
)
نشر من قبل
EDA Publishing Association
تاريخ النشر
2008
مجال البحث
الهندسة المعلوماتية
والبحث باللغة
English
تأليف
J. Moulin
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Recent advances in microtechnology allow realization of planar microcoils. These components are integrated in MEMS as magnetic sensor or actuator. In the latter case, it is necessary to maximize the effective magnetic field which is proportional to the current passing through the copper track and depends on the distance to the generation microcoil. The aim of this work was to determine the optimal microcoil design configuration for magnetic field generation. The results were applied to magnetic actuation, taking into account technological constraints. In particular, we have considered different realistic configurations that involve a magnetically actuated device coupled to a microcoil. Calculations by a semi-analytical method using Matlab software were validated by experimental measurements. The copper planar microcoils are fabricated by U.V. micromoulding on different substrates: flexible polymer (Kapton) and silicate on silicon. They are constituted by a spiral-like continuous track. Their total surface is about 1 mm2.
قيم البحث
اقرأ أيضاً
This paper presents a new electrostatic MEMS (MicroElectroMechanical System) based on a single high reliability totally free flexible membrane. Using four electrodes, this structure enables four states which allowed large deflections (4$mu$m) with lo
w actuation voltage (7,5V). This design presents also a good contact force and improve the restoring force of the structure. As an example of application, a Single Pole Double Throw (SPDT) for 24GHz applications, based on this design, has been simulated.
The resonant state expansion (RSE), a novel perturbation theory of Brillouin-Wigner type developed in electrodynamics [Muljarov, Langbein, and Zimmermann, Europhys. Lett., 92, 50010(2010)], is applied to planar, effectively one-dimensional optical sy
stems, such as layered dielectric slabs and Bragg reflector microcavities. It is demonstrated that the RSE converges with a power law in the basis size. Algorithms for error estimation and their reduction by extrapolation are presented and evaluated. Complex eigenfrequencies, electro-magnetic fields, and the Greens function of a selection of optical systems are calculated, as well as the observable transmission spectra. In particular we find that for a Bragg-mirror microcavity, which has sharp resonances in the spectrum, the transmission calculated using the resonant state expansion reproduces the result of the transfer/scattering matrix method.
Enhancement of the number and array density of nozzles within an inkjet head chip is one of the keys to raise the printing speed and printing resolutions. However, traditional 2D architecture of driving circuits can not meet the requirement for high
scanning speed and low data accessing points when nozzle numbers greater than 1000. This paper proposes a novel architecture of high-selection-speed three-dimensional data registration for inkjet applications. With the configuration of three-dimensional data registration, the number of data accessing points as well as the scanning lines can be greatly reduced for large array inkjet printheads with nozzles numbering more than 1000. This IC (Integrated Circuit) architecture involves three-dimensional multiplexing with the provision of a gating transistor for each ink firing resistor, where ink firing resistors are triggered only by the selection of their associated gating transistors. Three signals: selection (S), address (A), and power supply (P), are employed together to activate a nozzle for droplet ejection. The smart printhead controller has been designed by a 0.35 um CMOS process with a total circuit area, 2500 x 500 microm2, which is 80% of the cirucuit area by 2D configuration for 1000 nozzles. Experiment results demonstrate the functionality of the fabricated IC in operation, signal transmission and a potential to control more than 1000 nozzles with only 31 data access points and reduced 30% scanning time.
We present a numerical study of the application of the Shannon entropy technique to the planar restricted three-body problem in the vicinity of first-order interior mean-motion resonances with the perturber. We estimate the diffusion coefficient for
a series of initial conditions and compare the results with calculations obtained from the time evolution of the variance in the semimajor-axis and eccentricity plane. Adopting adequate normalization factors, both methods yield comparable results, although much shorter integration times are required for entropy calculations. A second advantage of the use of entropy is that it is possible to obtain reliable results even without the use of ensembles or analysis restricted to surfaces of section or representative planes. This allows for a much more numerically efficient tool that may be incorporated into a working N-body code and applied to numerous dynamical problems in planetary dynamics. Finally, we estimate instability times for a series of initial conditions in the 2/1 and 3/2 mean-motion resonances and compare them with times of escape obtained from directed N-body simulations. We find very good agreement in all cases, not only with respect to average values but also in their dispersion for near-by trajectories
Copper carbodiimide, CuNCN, is a geometrically frustrated nitrogen-based analogue of cupric oxide, whose magnetism remains ambiguous. Here, we employ a combination of local-probe techniques, including $^{63,, 65}$Cu nuclear quadrupole resonance, $^{1
3}$C nuclear magnetic resonance and muon spin rotation to show that the magnetic ground state of the Cu$^{2+}$ ($S=1/2$) spins is frozen and disordered. Moreover, these complementary experiments unequivocally establish an onset of intrinsically inhomogeneous magnetic state at $T_h=80$ K. Below $T_h$, the low-temperature frozen component coexist with the remnant high-temperature dynamical component down to $T_l = 20$ K, where the latter finally ceases to exist. Based on a scaling of internal magnetic fields of both components we conclude that the two components coexist on a microscopic level.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
