اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدLow-frequency Noise in Josephson Junctions for Superconducting Qubits
84
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We have studied low-frequency resistance fluctuations in shadow-evaporated Al/AlOx/Al tunnel junctions. Between 300 K and 5 K the spectral density follows a 1/f-law. Below 5 K, individual defects distort the 1/f-shape of the spectrum. The spectral density decreases linearly with temperature between 150 K and 1 K and saturates below 0.8 K. At 4.2 K, the spectral density is about two orders of magnitude lower than expected from a recent survey [D. J. Van Harlingen et al., Phys. Rev. B 70, 064510 (2004)]. Due to the saturation below 0.8 K the estimated qubit dephasing times at 100 mK are only about two times longer than calculated by Van Harlingen et al.
قيم البحث
اقرأ أيضاً
We study the effects of correlated low frequency noise sources acting on a two qubit gate in a fixed coupling scheme. A phenomenological model for the spatial and cross-talk correlations is introduced. The decoherence inside the SWAP subspace is anal
ysed by combining analytic results based on the adiabatic approximation and numerical simulations. Results critically depend on amplitude of the low frequency noise with respect to the qubits coupling strength. Correlations between noise sources induce qualitative different behaviors depending on the values of the above parameters. The possibility to reduce dephasing due to correlated low frequency noise by a recalibration protocol is discussed.
New technology for superconductor integrated circuits has been developed and is presented. It employs diffusion stoplayers (DSLs) to protect Josephson junctions (JJs) from interlayer migration of impurities, improve JJ critical current (Ic) targeting
and reproducibility, eliminate aging, and eliminate pattern-dependent effects in Ic and tunneling characteristics of Nb/Al/AlOx/Nb junctions in integrated circuits. The latter effects were recently found in Nb-based JJs integrated into multilayered digital circuits. E.g., it was found that Josephson critical current density (Jc) may depend on the JJs environment, on the type and size of metal layers making contact to niobium base (BE) and counter electrodes (CE) of the junction, and also change with time. Such Jc variations within a circuit reduce circuit performance and yield, and restrict integration scale. This variability of JJs is explained as caused by hydrogen contamination of Nb layers during wafer processing, which changes the height and structural properties of AlOx tunnel barrier. Redistribution of hydrogen impurities between JJ electrodes and other circuit layers by diffusion along Nb wires and through contacts between layers causes long-term drift of Jc. At least two DSLs are required to completely protect JJs from impurity diffusion effects - right below the junction BE and right above the junction CE. The simplest and the most technologically convenient DSLs we have found are thin (from 3 nm to 10 nm) layers of Al. They were deposited in-situ under the BE layer, thus forming an Al/Nb/Al/AlOx/Nb penta-layer, and under the first wiring layer to junctions CE, thus forming an Al/Nb wiring bi-layer. A significant improvement of Jc uniformity on 150-mm wafer has also been obtained along with large improvements in Jc targeting and run-to-run reproducibility.
Fabrication of sub-micron Josephson junctions is demonstrated using standard processing techniques for high-coherence, superconducting qubits. These junctions are made in two separate lithography steps with normal-angle evaporation. Most significantl
y, this work demonstrates that it is possible to achieve high coherence with junctions formed on aluminum surfaces cleaned in situ with Ar milling before the junction oxidation. This method eliminates the angle-dependent shadow masks typically used for small junctions. Therefore, this is conducive to the implementation of typical methods for improving margins and yield using conventional CMOS processing. The current method uses electron-beam lithography and an additive process to define the top and bottom electrodes. Extension of this work to optical lithography and subtractive processes is discussed.
We present the analysis of the mean switching time and its standard deviation of short overdamped Josephson junctions, driven by a direct current and a periodic signal. The effect of noise enhanced stability is investigated. It is shown that fluctuat
ions may both decrease and increase the switching time.
Josephson junctions have broad applications in metrology, quantum information processing, and remote sensing. For these applications, the electronic noise is a limiting factor. In this work we study the thermal noise in narrow Josephson junctions usi
ng a tight-binding Hamiltonian. For a junction longer than the superconducting coherence length, several self-consistent gap profiles appear close to a phase difference $pi$. They correspond to two stable solutions with an approximately constant phase-gradient over the thin superconductor connected by a $2pi$ phase slip, and a solitonic branch. The current noise power spectrum has pronounced peaks at the transition frequencies between the different states in each branch. We find that the noise is reduced in the gradient branches in comparison to the zero-length junction limit. In contrast, the solitonic branch exhibits an enhanced noise and a reduced current due to the pinning of the lowest excitation energy to close to zero energy.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
