اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدHypersonic curved compression ramp flows with bistable states
87
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The bistable states and separation hysteresis in curved compression ramp (CCR) flows, and the corresponding aerothermal characteristics (including wall friction, pressure and heat flux), are studied numerically and theoretically. Direct numerical simulations of separation hysteresis induced by variation of turning angle, as well as the influence of inflow Mach number and wall temperature on hysteresis loops, are carried out. Distributions of wall friction, pressure and heat flux are analyzed. Further, emergence of wall frictions first and second minima in the separation bubble is interpreted, revealing it is dominated by the adverse pressure gradient induced by separation and reattachment shocks. The present results and analysis indicate that the reversed-flow singularity of Smith (Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences, 1988, 420: 21-52) is less likely to occur in CCR flows. The prediction of peak pressure of separation states confirms the model based on the minimum viscous dissipation theorem (Physics of Fluids, 2020, 32(10):101702). While the pressure overshoot can be analyzed by shock-polars with pressure match of compression and expansion process. The correlation between peak heat flux and peak pressure rise of both separation and attachment states is also discussed in terms of the classical power relations.
قيم البحث
اقرأ أيضاً
A new spatial-related mechanism is proposed to understand separation hysteresis processes in curved compression ramp (CCR) flows discovered recently (Hu et al. Phy. Fluid, 32(11): 113601, 2020). Two separation hystereses, induced by variations of Mac
h number and wall temperature, are investigated numerically. The two hystereses indicate that there must exist parameter intervals of Mach number and wall temperature, wherein both attachment and separation states can be established stably. The relationships between the aerodynamic characteristics (including wall friction, pressure and heat flux) and the shock wave configurations in this two hystereses are analyzed. Further, the adverse pressure gradient (APG) Isb(x) induced by the upstream separation process and APG Icw(x) induced by the downstream isentropic compression process are estimated by classic theories. The trend of boundary layer APG resistence Ib(x) is evaluated from the spatial distributions of the physical quantities such as the shape factor and the height of the sound velocity line. With the stable conditions of separation and attachment, a self-consistent mechanism is obtained when Isb, Icw and Ib have appropriate spatial distributions.
Here, we provide a theoretical framework revealing that a steady compression ramp flow must have the minimal dissipation of kinetic energy, and can be demonstrated using the least action principle. For a given inflow Mach number $M_{0}$ and ramp angl
e $alpha$, the separation angle $theta_{s}$ manifesting flow system states can be determined based on this theory. Thus, both the shapes of shock wave configurations and pressure peak $p_{peak}$ behind reattachment shock waves are predictable. These theoretical predictions agree excellently with both experimental data and numerical simulations, covering a wide range of $M_{0}$ and $alpha$. In addition, for a large separation, the theory indicates that $theta_{s}$ only depends on $M_{0}$ and $alpha$, but is independent of the Reynolds number $Re$ and wall temperature $T_{w}$. These facts suggest that the proposed theoretical framework can be applied to other flow systems dominated by shock waves, which are ubiquitous in aerospace engineering.
In this paper, the relation between skin friction and heat transfer along windward sides of blunt-nosed bodies in hypersonic flows is investigated. The self-similar boundary layer analysis is accepted to figure out the distribution of the ratio of sk
in friction to heat transfer coefficients along the wall. It is theoretically obtained that the ratio depends linearly on the local slope angle of the wall surface, and an explicit analogy expression is presented for circular cylinders, although the linear distribution is also found for other nose shapes and even in gas flows with chemical reactions. Furthermore, based on the theoretical modelling of the second order shear and heat transfer terms in Burnett equations, a modified analogy is derived in the near continuum regime by considering the rarefied gas effects. And a bridge function is also constructed to describe the nonlinear analogy in the transition flow regime. At last, the direct simulation Monte Carlo method is used to validate the theoretical results. The general analogy, beyond the classical Reynolds analogy, is applicable to both flat plates and blunt-nosed bodies, in either continuous or rarefied hypersonic flows.
A new method for the localization of the regions where small scale turbulent fluctuations are present in hypersonic flows is applied to the large-eddy simulation (LES) of a compressible turbulent jet with an initial Mach number equal to 5. The locali
zation method used is called selective LES and is based on the exploitation of a scalar probe function $f$ which represents the magnitude of the stretching-tilting term of the vorticity equation normalized with the enstrophy (Tordella et al. 2007). For a fully developed turbulent field of fluctuations, statistical analysis shows that the probability that $f$ is larger than 2 is almost zero, and, for any given threshold, it is larger if the flow is under-resolved. By computing the spatial field of $f$ in each instantaneous realization of the simulation it is possible to locate the regions where the magnitude of the normalized vortical stretching-tilting is anomalously high. The sub-grid model is then introduced into the governing equations in such regions only. The results of the selective LES simulation are compared with those of a standard LES, where the sub-grid terms are used in the whole domain, and with those of a standard Euler simulation with the same resolution. The comparison is carried out by assuming as reference field a higher resolution Euler simulation of the same jet. It is shown that the selective LES modifies the dynamic properties of the flow to a lesser extent with respect to the classical LES. In particular, the prediction of the enstrophy, mean velocity and density distributions and of the energy and density spectra are substantially improved.
Wall cooling has substantial effects on the development of instabilities and transition processes in hypersonic boundary layers (HBLs). A sequence of linear stability theory, two-dimensional and non-linear three-dimensional DNSs is used to analyze Ma
ch~6 boundary layers, with wall temperatures ranging from near-adiabatic to highly cooled conditions, where the second-mode instability radiates energy. Fluid-thermodynamic analysis shows that this radiation comprises both acoustic as well as vortical waves. 2D simulations show that the conventional trapped nature of second-mode instability is ruptured. Although the energy efflux of both acoustic and vortical components increases with wall-cooling, the destabilization effect is much stronger and no significant abatement of pressure perturbations is realized. In the near-adiabatic HBL, the wavepacket remains trapped within the boundary layer and attenuates outside the region of linear instability. However, wavepackets in the cooled-wall HBLs amplify and display nonlinear distortion, and transition more rapidly. The structure of the wavepacket displays different behavior; moderately-cooled walls show bifurcation into a leading turbulent head region and a trailing harmonic region, while highly-cooled wall cases display lower convection speeds and significant wavepacket elongation, with intermittent spurts of turbulence in the wake of the head region. This elongation effect is associated with a weakening of the lateral jet mechanism due to the breakdown of spanwise coherent structures. In moderately cooled-walls, the spatially-localized wall loading is due to coherent structures in the leading turbulent head region. In highly-cooled walls, the elongated near-wall streaks in the wake region of the wavepacket result in more than twice as large levels of skin friction and heat transfer over a sustained period of time.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
