اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدExperimental and numerical characterization of single-phase pressure drop and heat transfer enhancement in helical corrugated tubes
117
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The internal flow in corrugated tubes of different helical pitch, covering from the laminar to turbulent regime, was studied in order to characterize the three-dimensional flow and the influence of corrugation geometry on pressure drop and convective heat transfer. With water as working fluid and an imposed wall heat flux, ranging from around 4 to 33 kW/m2, a numerical model was developed with a CFD commercial software, where k-omega SST was used to model turbulence. Experimental tests were performed covering Reynolds numbers in the range from around 300 up to 5000, which allowed to identify the transition region and validate the numerical model. The results show that due to the swirl induced by the corrugation, the critical Reynolds number for the start of transition to turbulent flow is reduced. The thermal performance factor, which quantifies the heat transfer enhancement at the expense of pressure drop, was used to compare the corrugated tubes against the reference case of smooth tube. Based on this, all investigated corrugated geometries performed better than the smooth tube, except for low Reynolds numbers (Re<500) in the laminar regime. Overall, the corrugated tube with the lowest pitch showed a clearly better performance for the intermediate range of Reynolds numbers (1000<Re<2300), being an optimal choice for a wider range of operating conditions in the transitional and turbulent flow regimes.
قيم البحث
اقرأ أيضاً
In this numerical study on Rayleigh-Benard convection we seek to improve the heat transfer by passive means. To this end we introduce a single tilted conductive barrier centered in an aspect ratio one cell, breaking the symmetry of the geometry and t
o channel the ascending hot and descending cold plumes. We study the global and local heat transfer and the flow organization for Rayleigh numbers $10^5 leq Ra leq 10^9$ for a fixed Prandtl number of $Pr=4.3$. We find that the global heat transfer can be enhanced up to $18%$, and locally around $800%$. The averaged Reynolds number is always decreased when a barrier is introduced, even for those cases where the global heat transfer is increased. We map the entire parameter space spanned by the orientation and the size of a single barrier for $Ra=10^8$.
We study hydrodynamics, heat transfer and entropy generation in pressure-driven microchannel flow of a power-law fluid. Specifically, we address the effect of asymmetry in the slip boundary condition at the channel walls. Constant, uniform but unequa
l heat fluxes are imposed at the walls in this thermally developed flow. The effect of asymmetric slip on the velocity profile, on the wall shear stress, on the temperature distribution, on the Bejan number profiles, and on the average entropy generation and the Nusselt number are established through the numerical evaluation of exact analytical expressions derived. Specifically, due to asymmetric slip, the fluid momentum flux and thermal energy flux are enhanced along the wall with larger slip, which in turn shifts the location of the velocitys maximum to an off-center location closer to the said wall. Asymmetric slip is also shown to redistribute the peaks and plateaus of the Bejan number profile across the microchannel, showing a sharp transition between entropy generation due to heat transfer and due to fluid flow at an off-center-line location. In the presence of asymmetric slip, the difference in the imposed heat fluxes leads to starkly different Bejan number profiles depending on which wall is hotter, and whether the fluid is shear-thinning or shear-thickening. Overall, slip is shown to promote uniformity in both the velocity field and the temperature field, thereby reducing irreversibility in this flow.
Compact and small-scale heat exchangers can handle high heat dissipation rates due to their large surface area to volume ratios. Applications involving high heat dissipation rates include, but are not limited to, compact microelectronic processing un
its, high power laser arrays, fuel cells, as well as fission batteries. Low maintenance cost, small size and dimensions, as well as high convective heat transfer coefficients, make micro-scale heat sinks an efficient and reliable cooling solution for applications with high heat dissipation rates. Despite these advantages, the large pressure drop that occurs within micro-scale heat sinks has restricted their utilization. Slip at the walls of microchannels has been reported to reduce friction factor up to 30%, depending on the hydraulic diameter of the microchannel. Numerical investigations are conducted to comprehensively investigate the effect of slip at walls on friction factor and Nusselt number of liquid flows in micro-scale heat sinks. At the same mass flow rate and inlet Reynolds number, obtained results suggest that slip length on the order of 2 microns enhances the overall thermalhydraulic performance of micro heat sinks by almost 6% in comparison with no-slip boundary conditions. 4% increase is observed in channel average Nusselt number while pumping power reduces by 8% in comparison with no-slip boundary condition.
The physics of foams and emulsions has traditionally been studied using bulk foam/emulsion tests and single film platforms such as the Scheludko cell. Recently there has been a renewed interest in a third class of techniques that we term as single bu
bble/drop tests, which employ isolated whole bubbles and drops to probe the characteristics of foams and emulsions. Single bubble and drop techniques provide a convenient framework for investigating a number of important characteristics of foams and emulsions, including the rheology, stabilization mechanisms, and rupture dynamics. In this review we provide a comprehensive discussion of the various single bubble/drop platforms and the associated experimental measurement protocols including the construction of coalescence time distributions, visualization of the thin film profiles and characterization of the interfacial rheological properties. Subsequently, we summarize the recent developments in foam and emulsion science with a focus on the results obtained through single bubble/drop techniques. We conclude the review by presenting important venues for future research.
We present a numerical study of quasistatic magnetoconvection in a cubic Rayleigh-Benard (RB) convection cell subjected to a vertical external magnetic field. For moderate values of the Hartmann number Ha, we find an enhancement of heat transport. Fu
rthermore, a maximum heat transport enhancement is observed at certain optimal $Ha_{opt}$. The enhanced heat transport may be understood as a result of the increased coherency of the thermal plumes, which are elementary heat carriers of the system. To our knowledge this is the first time that a heat transfer enhancement by the stabilising Lorentz force in quasistatic magnetoconvection has been observed. We further found that the optimal enhancement may be understood in terms of the crossing between the thermal and the momentum boundary layers (BL) and the fact that temperature fluctuations are maximum near the position where the BLs cross. These findings demonstrate that the heat transport enhancement phenomenon in the quasistatic magnetoconvection system belongs to the same universality class of stabilising$-$destabilising ($S$-$D$) turbulent flows as the systems of confined Rayleigh-Benard (CRB), rotating Rayleigh-Benard (RRB) and double-diffusive convection (DDC). This is further supported by the findings that the heat transport, boundary layer ratio and the temperature fluctuations in magnetoconvection at the boundary layer crossing point are similar to the other three cases.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
