اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEffect of Al content on the hardness and thermal stability study of AlTiN and AlTiBN coatings deposited by HiPIMS
174
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The microstructure, mechanical properties and thermal stability of AlTiN and AlTiBN coatings grown by reactive high-power impulse magnetron sputtering (HiPIMS) have been analyzed as a function of Al/(Al+Ti) ratio, x, between 0.5 and 0.8. The coatings were predominantly formed by a face-centered cubic Ti(Al)N crystalline phase, both with and without B, even for x ratios as high as 0.6, which is higher than the ratio typically encountered for AlTiN coatings deposited by reactive magnetron sputtering. B doping, in combination with the highly energetic deposition conditions offered by HiPIMS, results in the suppression of the columnar grain morphology typically encountered in AlTiN coatings. On the contrary, the AlTiBN coatings grown by HiPIMS present a dense nanocomposite type microstructure, formed by nanocrystalline Ti(Al)N domains and amorphous regions composed of Ti(Al)B2 and BN. As a result, high-Al content (x>0.6) AlTiBN coatings grown by HiPIMS offer higher hardness, elasticity and fracture toughness than AlTiN coatings. Moreover, the thermal stability and the hot hardness are substantially enhanced, delaying the onset of formation of the detrimental hexagonal AlN phase from 850 C in the case of AlTiN, to 1000 C in the case of AlTiBN.
قيم البحث
اقرأ أيضاً
The wide band gap methylammonium lead bromide perovskite is promising for applications in tandem solar cells and light-emitting diodes. Despite its utility, there is only a limited understanding of its reproducibility and stability. Herein, the depen
dence of the properties, performance, and shelf storage of thin films and devices on minute changes to the precursor solution stoichiometry is examined in detail. Although photovoltaic cells based on these solution changes exhibit similar initial performance, the shelf-storage depends strongly on the precursor solution stoichiometry. While all devices exhibit some degree of healing, the bromide-deficient films show a remarkable improvement, more than doubling in their photoconversion efficiency. Photoluminescence spectroscopy experiments performed under different atmospheres suggest that this increase is due in part to a trap healing mechanism that occurs upon exposure to the environment. Our results highlight the importance of understanding and manipulating defects in lead halide perovskites to produce long-lasting, stable devices.
Antisolvent crystallization methods are frequently used to fabricate high-quality perovskite thin films, to produce sizable single crystals, and to synthesize nanoparticles at room temperature. However, a systematic exploration of the effect of speci
fic antisolvents on the intrinsic stability of multicomponent metal halide perovskites has yet to be demonstrated. Here, we develop a high-throughput experimental workflow that incorporates chemical robotic synthesis, automated characterization, and machine learning techniques to explore how the choice of antisolvent affects the intrinsic stability of binary perovskite systems in ambient conditions over time. Different combinations of the endmembers, MAPbI3, MAPbBr3, FAPbI3, FAPbBr3, CsPbI3, and CsPbBr3, are used to synthesize 15 combinatorial libraries, each with 96 unique combinations. In total, roughly 1100 different compositions are synthesized. Each library is fabricated twice using two different antisolvents: toluene and chloroform. Once synthesized, photoluminescence spectroscopy is automatically performed every 5 minutes for approximately 6 hours. Non-negative Matrix Factorization (NMF) is then utilized to map the time- and compositional-dependent optoelectronic properties. Through the utilization of this workflow for each library, we demonstrate that the selection of antisolvent is critical to the stability of metal halide perovskites in ambient conditions. We explore possible dynamical processes, such as halide segregation, responsible for either the stability or eventual degradation as caused by the choice of antisolvent. Overall, this high-throughput study demonstrates the vital role that antisolvents play in the synthesis of high-quality multicomponent metal halide perovskite systems.
In this work, amorphous thin films in Mg-Si-O-N system were prepared in order to investigate the dependence of optical and mechanical properties on Mg composition. Reactive RF magnetron co-sputtering from magnesium and silicon targets were used for t
he deposition of Mg-Si-O-N thin films. Films were deposited on float glass, silica wafers and sapphire substrates in an Ar, N2 and O2 gas mixture. X-ray photoelectron spectroscopy, atomic force microscopy, scanning electron microscopy, spectroscopic ellipsometry, and nanoindentation were employed to characterize the composition, surface morphology, and properties of the films.
Size dependent hardness has long been reported in nanosized indentations, however the corresponding explanation is still in exploration. In this paper, we examine the influence of surface energy on the hardness of materials under spherical indentatio
n. To evaluate the ability of materials to resist indentation, a yield hardness is defined here as the contact pressure at the inception of material yield. It is found that this defined hardness is an intrinsic material property depending only on the yield strength and Poisson ratio in conventional continuum mechanics. Then, the impact of surface energy on the yield hardness is analyzed through finite element simulations. By using the dimensional analysis, the dependences of the yield hardness and critical indent depth at yield initiation on surface energy have been achieved. When the yield strength is comparable to the ratio of surface energy density to indenter radius, surface energy will alter the yield hardness and the critical indent depth. As the size of indenter decreases to nanoscale, both the yield hardness and the indent depth will increase significantly. This study provides a possible clarification to the size dependence of hardness and a potential approach to measure the yield strength and surface energy of solids through nanosized indentations.
Ceramic dual-phase oxygen transport membranes with the composition of 60wt.% Ce0.9Pr0.1O2-{delta}-40wt.%Pr0.6Sr0.4Fe1-xAlxO3-{delta} (x = 0.05, 0.1, 0.2, 0.3, 0.4, 0.6, 0.8, 1.0) (60CPO-40PSF1-xAxO) based on 60Ce0.9Pr0.1O2-{delta}-40Pr0.6Sr0.4FeO3-{d
elta} doped Al was successfully synthesized through a modified Pechini method. Crystal structure, surface microtopography and oxygen permeability are investigated systematically. The cell parameters of perovskite phase first increased and then decreased with the increase of Al content, which is related to the radius of the Al3+ and the formation of impurity phase. As x ranges from 0.1 to 0.8, the oxygen permeability of the materials first increases and then decreases, and the maximum value of oxygen permeation rate for 60CPO-40PSF1-xAxO membranes with 0.4mm thickness at 1000 {deg}C is 1.12 mL min-1 cm-2 when x = 0.4. XRD measurements revealed high temperature stability and CO2-tolerant property of the dual-phase composites. The partial replacement of Fe$^{3+}$/Fe$^{4+}$ by Al$^{3+}$ causes the material not only to exhibit good stability, but also to increase the oxygen permeability of the membranes.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
