اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدTowards 3D-Printed Inverse-Designed Metaoptics
80
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Optical metasurfaces have been heralded as the platform to integrate multiple functionalities in a compact form-factor, potentially replacing bulky components. A central stepping stone towards realizing this promise is the demonstration of multifunctionality under several constraints (e.g. at multiple incident wavelengths and/or angles) in a single device -- an achievement being hampered by design limitations inherent to single-layer planar geometries. Here, we propose a general framework for the inverse design of volumetric 3D metaoptics via topology optimization, showing that even few-wavelength thick devices can achieve high-efficiency multifunctionality. We embody our framework in multiple closely-spaced patterned layers of a low-index polymer. We experimentally demonstrate our approach with an inverse-designed 3d-printed light concentrator working at five different non-paraxial angles of incidence. Our framework paves the way towards realizing multifunctional ultra-compact 3D nanophotonic devices.
قيم البحث
اقرأ أيضاً
The ability of photonic crystal waveguides (PCWs) to confine and slow down light makes them an ideal component to enhance the performance of various photonic devices, such as optical modulators or sensors. However, the integration of PCWs in photonic
applications poses design challenges, most notably, engineering the PCW mode dispersion and creating efficient coupling devices. Here, we solve these challenges with photonic inverse design, and experimentally demonstrate a slow-light PCW optical phased array (OPA) with a wide steering range. Even and odd mode PCWs are engineered for a group index of 25, over a bandwidth of 20nm and 12nm, respectively. Additionally, for both PCW designs, we create strip waveguide couplers and free-space vertical couplers. Finally, also relying on inverse design, the radiative losses of the PCW are engineered, allowing us to construct OPAs with a 20{deg} steering range in a 20nm bandwidth.
Ultrashort photoemitted electron bunches can provide high electron currents within sub-picosecond timeframes, enabling time-resolved investigations of ultrafast physical processes with nanoscale resolution. Non-resonant conductive nanotips are typica
lly employed to realize nanoscale photoelectron sources with high brightness. However, such emitters require complex non-scalable fabrication procedures featuring poor reproducibility. Planar resonant antennas fabricated via photolithography have been recently investigated, also because of their superior field enhancement properties. Nevertheless, the electron emission from these structures is parallel to the substrate plane, which limits their practical use as electron sources. In this work, we present an innovative out-of-plane, resonant nanoantenna design for field-driven photoemission enabled by high-resolution 3D printing. Numerical and experimental evidences demonstrate that gold-coated, terahertz resonant nanocones provide large local electric fields at their apex, automatically ensuring out-of-plane coherent electron emission and acceleration. We show that the resonant structures can be conveniently arranged in an array form, for a further significant electron extraction enhancement via a collective terahertz response. Remarkably, such collective behaviour can also be harvested to boost photoemission from an individual nano-source. Our approach opens the path for a new generation of photocathodes that can be reproducibly fabricated and designed at will, significantly relaxing the requirement for intense terahertz drivers.
Nonreciprocal devices such as isolators and circulators are key enabling technologies for communication systems, both at microwave and optical frequencies. While nonreciprocal devices based on magnetic effects are available for free-space and fibre-o
ptic communication systems, their on-chip integration has been challenging, primarily due to the concomitant high insertion loss, weak magneto-optical effects, and material incompatibility. We show that Kerr nonlinear resonators can be used to achieve all-passive, low-loss, bias-free, broadband nonreciprocal transmission and routing for applications in photonic systems such as chip-scale LIDAR. A multi-port nonlinear Fano resonator is used as an on-chip, all-optical router for frequency comb based distance measurement. Since time-reversal symmetry imposes stringent limitations on the operating power range and transmission of a single nonlinear resonator, we implement a cascaded Fano-Lorentzian resonator system that overcomes these limitations and significantly improves the insertion loss, bandwidth and non-reciprocal power range of current state-of-the-art devices. This work provides a platform-independent design for nonreciprocal transmission and routing that are ideally suited for photonic integration.
Additive manufacturing strives to combine any combination of materials into three dimensional functional structures and devices, ultimately opening up the possibility of 3D printed machines. It remains difficult to actuate such devices, thus limiting
the scope of 3D printed machines to passive devices or necessitating the incorporation of external actuators that are manufactured differently. Here we explore 3D printed hybrid thermoplast/conducter bilayers, that can be actuated by differential heating caused by externally controllable currents flowing through their conducting faces. We uncover the functionality of such actuators and show that they allow to 3D print, in one pass, simple flexible robotic structures that propel forward under step-wise applied voltages. Moreover, exploiting the thermoplasticity of the non-conducting plastic parts at elevated temperatures, we show how strong driving leads to irreversible deformations - a form of 4D printing - which also enlarges the range of linear response of the actuators. Finally, we show how to leverage such thermoplastic relaxations to accumulate plastic deformations and obtain very large deformations by alternatively driving both layers of a bilayer; we call this ratcheting. Our strategy is scalable and widely applicable, and opens up a new approach to reversible actuation and irreversible 4D printing of arbitrary structures and machines.
The advancement of 3D-printing opens up a new way of constructing affordable custom terahertz (THz) components due to suitable printing resolution and THz transparency of polymer materials. We present a way of calculating, designing and fabricating a
THz waveplate that phase-modulates an incident THz beam ({lambda}=2.14 mm) in order to create a predefined intensity profile of the optical wavefront on a distant image plane. Our calculations were performed for two distinct target intensities with the use of a modified Gerchberg-Saxton algorithm. The resulting phase-modulating profiles were used to model the polyactide elements, which were printed out with a commercially available 3D-printer. The results were tested in an THz experimental setup equipped with a scanning option and they showed good agreement with theoretical predictions.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
