اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEffect of stand-off distance and spatial resolution on the pressure impact of near-wall vapor bubble collapses
165
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We consider the collapse behavior of cavitation bubbles near walls under high ambient pressure conditions. Generic configurations with different stand-off distances are investigated by numerical simulation using a fully compressible two-phase flow solver including phase change. The results show that the stand-off distance has significant effects on collapse dynamics, micro-jet formation, rebound, and maximum wall pressure. A relation between cavitation induced material damage and corresponding collapse mechanisms is obtained from pressure-impact data at the wall. We analyze the resolution dependence of collapse and rebound and the observed maximum pressure distributions. The comparison of the results on six different grid resolutions shows that main collapse features are already captured on the coarsest resolution, while the peak pressures are strongly resolution dependent.
قيم البحث
اقرأ أيضاً
We numerically investigate the effect of non-condensable gas inside a vapor bubble on bubble dynamics, collapse pressure and pressure impact of spherical and aspherical bubble collapses. Free gas inside a vapor bubble has a damping effect that can we
aken the pressure wave and enhance the bubble rebound. To estimate this effect numerically, we derive and validate a multi-component model for vapor bubbles containing gas. For the cavitating liquid and the non-condensable gas, we employ a homogeneous mixture model with a coupled equation of state for all components. The cavitation model for the cavitating liquid is a barotropic thermodynamic equilibrium model. Compressibility of all phases is considered in order to capture the shock wave of the bubble collapse. After validating the model with an analytical energy partitioning model, simulations of collapsing wall-attached bubbles with different stand-off distances are performed. The effect of the non-condensable gas on rebound and damping of the emitted shock wave is well captured.
Dynamics of a bubble impacting and sliding a tilted surface has been investigated through experimental and computational methods. textcolor{blue}{Specifically, shear stress generated on the wall has been calculated and compared with bacterium adhesio
n force in order to evaluate a potential sanitization function. In experiments, the bubble-wall interaction has been characterized for several different wall angles. We numerically solved a force balance including buoyancy, hydrodynamic inertia & drag, lift and thin film force to determine the bubble motion. Results showed that the shear stress increases with the wall inclination. The maximum shear stress goes up to more than 300 Pa as a single bubble impacts and scrubs a tilted wall. We found that such a high shear stress is attributed to a rapid change in thin film curvature (flipping bubble/water interface) during the bouncing stage. Later, during the sliding stage, a smaller shear stress up to around 45 Pa is generated for a longer period of time. We also showed that the shear stress generated during the bouncing and sliding stages is high enough to remove bacteria from a surface as a potential method for removing bacteria from tilted surfaces.
Deformation-induced lateral migration of a bubble slowly rising near a vertical plane wall in a stagnant liquid is numerically and theoretically investigated. In particular, our focus is set on a situation with a small clearance $c$ between the bubbl
e interface and the wall. Motivated by the fact that experimentally measured migration velocity (Takemura et al. (2002, J. Fluid Mech. {bf 461}, 277)) is higher than the velocity estimated by the available analytical solution (Magnaudet et al. (2003, J. Fluid Mech. {bf 476}, 115)) using the Fax{e}n mirror image technique for $kappa(=a/(a+c))ll 1$ (here $a$ is the bubble radius), when the clearance parameter $epsilon(=c/a)$ is comparable to or smaller than unit, the numerical analysis based on the boundary-fitted finite-difference approach by solving the Stokes equation is performed to complement the experiment. To improve the understandings of a role of the squeezing flow within the bubble-wall gap, the theoretical analysis based on a soft-lubrication approach (Skotheim & Mahadevan (2004, Phys. Rev. Lett. {bf 92}, 245509)) is also performed. The present analyses demonstrate the migration velocity scales $propto{rm Ca} epsilon^{-1}V_{B1}$ (here, $V_{B1}$ and ${rm Ca}$ denote the rising velocity and the capillary number, respectively) in the limit of $epsilonto 0$.
Deformation-induced lateral migration of a bubble slowly rising near a vertical plane wall in a stagnant liquid is numerically and theoretically investigated. In particular, our focus is set on a situation with a short clearance $c$ between the bubbl
e interface and the wall. Motivated by the fact that numerically and experimentally measured migration velocities are considerably higher than the velocity estimated by the available analytical solution using the Fax{e}n mirror image technique for $a/(a+c)ll 1$ (here $a$ is the bubble radius), when the clearance parameter $varepsilon(= c/a)$ is comparable to or smaller than unity, the numerical analysis based on the boundary-fitted finite-difference approach solving the Stokes equation is performed to complement the experiment. The migration velocity is found to be more affected by the high-order deformation modes with decreasing $varepsilon$. The numerical simulations are compared with a theoretical migration velocity obtained from a lubrication study of a nearly spherical drop, which describes the role of the squeezing flow within the bubble-wall gap. The numerical and lubrication analyses consistently demonstrate that when $varepsilonleq 1$, the lubrication effect makes the migration velocity asymptotically $mu V_{B1}^2/(25varepsilon gamma)$ (here, $V_{B1}$, $mu$, and $gamma$ denote the rising velocity, the dynamic viscosity of liquid, and the surface tension, respectively).
Hard particle erosion and cavitation damage are two main wear problems that can affect the internal components of hydraulic machinery such as hydraulic turbines or pumps. If both problems synergistically act together, the damage can be more severe an
d result in high maintenance costs. In this work, a study of the interaction of hard particles and cavitation bubbles is developed to understand their interactive behavior. Experimental tests and numerical simulations using computational fluid dynamics (CFD) were performed. Experimentally, a cavitation bubble was generated with an electric spark near a solid surface, and its interaction with hard particles of different sizes and materials was observed using a high-speed camera. A simplified analytical approach was developed to model the behavior of the particles near the bubble interface during its collapse. Computationally, we simulated an air bubble that grew and collapsed near a solid wall while interacting with one particle near the bubble interface. Several simulations with different conditions were made and validated with the experimental data. The experimental data obtained from particles above the bubble were consistent with the numerical results and analytical study. The particle size, density and position of the particle with respect to the bubble interface strongly affected the maximum velocity of the particles.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
