اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدPrinted tapered leaky-wave antennas for W-band frequencies
112
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Despite their great potential in communication and sensing applications, printed leaky-wave antennas have rarely been reported at mm-wave frequencies. In this paper, tapered leaky-wave antennas operating at 80 GHz are designed, fabricated and experimentally characterized. While most continuous leaky-wave antennas use subwavelength strips or other comparably small elements, in this work, the surface impedance is discretized very coarsely using only three square patches per period. With this architecture, a wide range of surface reactance can be achieved while maintaining a minimum feature size of the metallic pattern that is feasible for printed circuit fabrication. As the analytical solution for the bandstructure of sinusoidally modulated reactance surfaces is inaccurate for coarse discretization, we find it using full-wave simulation. In order to control side lobes effectively, we use a tapered aperture illumination according to the Taylor one-parameter distribution. A comprehensive experimental demonstration is presented, including near-field and far-field measurements. Therewith, we verify the designed aperture illumination and we reveal the origin of spurious far-field features. Side lobes are effectively suppressed and spurious radiation is reduced to -18 dB compared to the main lobe.
قيم البحث
اقرأ أيضاً
This paper proposes two spoof surface plasmon polariton (SSPP) leaky-wave antennas using periodically loaded patches above perfect electric conductor (PEC) and artificial magnetic conductor (AMC) ground planes, respectively. The SSPP leaky-wave anten
na is based on a SSPP transmission line, along which circular patches are periodically loaded on both sides to provide an additional momentum for phase matching with the radiated waves in the air. The PEC and AMC ground planes underneath the antenna reflect the radiated waves into the upward space, leading to an enhanced radiation gain. Both PEC- and AMC-grounded antenna prototypes are fabricated and measured in comparison with the one without any ground plane. The experimental results show that the PEC and AMC ground planes increase the radiation gain by approximately 3 dB within the operational frequency range 4.5-6.5 GHz. It also demonstrates that the AMC-grounded leaky-wave antenna, with a thickness of 0.08lambda at 6 GHz, features more compact profile than the PEC-grounded one (with a thickness of 0.3lambda at 6 GHz).
The paper includes two contributions. First, it proves that the series and shunt radiation components, corresponding to longitudinal and transversal electric fields, respectively, are always in phase quadrature in axially asymmetric periodic leaky-wa
ve antennas (LWAs), so that these antennas are inherently elliptically polarized. This fact is theoretically proven and experimentally illustrated by two case-study examples, a composite right/left-handed (CRLH) LWA and a series-fed patch (SFP) LWA. Second, it shows (for the case of the SFP LWA) that the axial ratio is controlled and minimized by the degree of axial asymmetry.
In this paper, a novel concept of a leaky-wave antenna is proposed, based on the use of Huygens metasurfaces. It consists of a parallel-plate waveguide in which the top plate is replaced by a bianisotropic metasurface of the Omega type. It is shown t
hat there is an exact solution to transform the guided mode into a leaky-mode with arbitrary control of the constant leakage factor and the pointing direction. Although the solution turns out to be periodic, only one Floquet mode is excited and radiates, even for electrically long periods. Thanks to the intrinsic spurious Floquet mode suppression, broadside radiation can be achieved without any degradation. Simulations with idealized reactance sheets verify the concept. Moreover, physical structures compatible with PCB fabrication have been proposed and designed, considering aspects such as the effect of losses. Finally, experimental results of two prototypes are presented and discussed.
Mass production of photonic integrated circuits requires high-throughput wafer-level testing. We demonstrate that optical probes equipped with 3D-printed elements allow for efficient coupling of light to etched facets of nanophotonic waveguides. The
technique is widely applicable to different integration platforms.
This paper presents an exact solution for a perfect conversion of a TM-polarized surface wave (SW) into a TM-polarized leaky-wave (LW) using a reciprocal and lossless penetrable metasurface (MTS) characterized by a scalar sheet impedance, located on
a grounded slab. In contrast to known realizations of leaky-wave antennas, the optimal surface reactance modulation which is found here ensures the absence of evanescent higher-order modes of the field Floquet-wave expansion near the radiating surface. Thus, all the energy carried by the surface wave is used for launching the single inhomogeneous plane wave into space without accumulation of reactive energy in the higher-order modes. It is shown that the resulting penetrable MTS exhibits variation from an inductive to a capacitive reactance passing through a resonance. The present formulation complements a previous paper of the authors in which a perfect conversion from TM-polarized SW to TE-polarized LW was found for impenetrable boundary conditions. Here, the solution takes into account the grounded slab dispersion and it is convenient for practical implementation.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
