اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدElectric current effects in spark plasma sintering: From the evidence of physical phenomenon to constitutive equation formulation
140
0
0.0
(
0
)
تأليف
Geuntak Lee
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The 3 heating modes are utilized to make ZrN powders have 3 different levels of the electric current density at the same temperature during spark plasma sintering (SPS). The constitutive equation of sintering for SPS is applied to the experimental porosity evolution of ZrN from three SPS modes, and this showed high electric current density increase the electric current assisted deformability value of ZrN pellets, resulting in a reduction of the flow stress. The electric current flow enhances the dislocation motion, which was experimentally proved and analyzed by modified Williamson-Hall equation applying to X-ray diffraction results, and the mechanical strength test of ZrN pellets.
قيم البحث
اقرأ أيضاً
A new flash (ultra-rapid) spark plasma sintering method applicable to various materials systems, regardless of their electrical resistivity, is developed. A number of powders ranging from metals to electrically insulative ceramics have been successfu
lly densified resulting in homogeneous microstructures within sintering times of 8-35 s. A finite element simulation reveals that the developed method, providing an extraordinary fast and homogeneous heating concentrated in the samples volume and punches, is applicable to all the different samples tested. The utilized uniquely controllable flash phenomenon is enabled by the combination of the electric current concentration around the sample and the confinement of the heat generated in this area by the lateral thermal contact resistance. The presented new method allows: extending flash sintering to nearly all materials, controlling sample shape by an added graphite die, and an energy efficient mass production of small and intermediate size objects. This approach represents also a potential venue for future investigations of flash sintering of complex shapes.
This work addresses the two great challenges of the spark plasma sintering (SPS) process: the sintering of complex shapes and the simultaneous production of multiple parts. A new controllable interface method is employed to concurrently consolidate t
wo nickel gear shapes by SPS. A graphite deformable sub-mold is specifically designed for the mutual densification of the both complex parts in a unique 40 mm powder deformation space. An energy efficient SPS configuration is developed to allow the sintering of a large-scale powder assembly under electric current lower than 900 A. The stability of the developed process is studied by electro-thermal-mechanical (ETM) simulation. The ETM simulation reveals that homogeneous densification conditions can be attained by inserting an alumina powder at the sample/punches interfaces enabling the energy efficient heating and the thermal confinement of the nickel powder. Finally, the feasibility of the fabrication of the two near net shape gears with a very homogeneous microstructure is demonstrated.
An energy efficient spark plasma sintering method enabling the densification of large size samples assisted by very low electric current levels is developed. In this method, the electric current is concentrated in the graphite foils around the sample
. High energy dissipation is then achieved in this area enabling the heating and full densification of large (alumina) parts ({{O}} 40 mm) at relatively low currents (800 A). The electrothermal mechanical simulation reveals that the electric current needed to heat the large samples is 70 % lower in the energy efficient configuration compared to the traditional configuration. The presence of thermal and densification gradients is also revealed for the larger size samples. Potential solutions for this problem are discussed. The experiments confirm the possibility of full densification (96-99 %) of large alumina samples. This approach allows using small (and low cost) SPS devices (generally limited to 10-15 mm samples) for large size samples (40-50 mm). The developed technique enables also an optimized energy consumption by large scale SPS systems.
Graphite creep has high importance for applications using high pressures (100 MPa) and temperatures close to 2000 {textdegree}C. In particular, the new flash spark plasma sintering process (FSPS) is highly sensitive to graphite creep when applied to
ultra-high temperature materials such as silicon carbide. In this flash process taking only a few seconds, the graphite tooling reaches temperatures higher than 2000 {textdegree}C resulting in its irreversible deformation. The graphite tooling creep prevents the flash spark plasma sintering process from progressing further. In this study, a finite element model is used to determine FSPS tooling temperatures. In this context, we explore the graphite creep onset for temperatures above 2000 {textdegree}C and for high pressures. Knowing the graphite high temperature limit, we modify the FSPS process so that the sintering occurs outside the graphite creep range of temperatures/pressures. 95 % dense silicon carbide compacts are obtained in about 30 s using the optimized FSPS.
Flash sintering phenomena are predominantly associated with ceramics due to thermal runaway of their electric conductivity noticeably represented in materials such as zirconia or silicon carbide. Because of their high electric conductivity, flash sin
tering of metals is nearly inexistent. In this work, an original metal powder flash sintering method based on a microwave approach is presented. Within the developed approach, an unusually fast (60 s) thermal and sintering runaway of Ti-6Al-4V powder is experimentally revealed under microwave illumination. This phenomenon is simulated based on an electromagnetic-thermal-mechanical (EMTM) model. The developed multiphysics model reveals that the metal powder specimens runaway does not result from its intrinsic material properties, but results from the resonance phenomenon thermally activated by the surrounding tooling material. The EMTM simulation predicts with a very good accuracy the microwave repartition and the resulting densification and powder specimens shape distortions observed experimentally. The comparison of the microwave and conventional sintering kinetics indicates an important acceleration of the sintering behavior under microwave heating. The developed sintering approach has a potential of the implementation for time-effective mass production of small metal parts.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
