اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدInterface-Confined Doubly Anisotropic Oxidation of Two-Dimensional MoS2
177
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Despite their importance, chemical reactions confined in a low dimensional space are elusive and experimentally intractable. In this work, we report doubly anisotropic, in-plane and out-of-plane, oxidation reactions of two-dimensional crystals, by resolving interface-confined thermal oxidation of a single and multilayer MoS2 supported on silica substrates from their conventional surface reaction. Using optical second-harmonic generation spectroscopy of artificially stacked multilayers, we directly proved that crystallographically oriented triangular oxides (TOs) were formed in the bottommost layer while triangular etch pits (TEs) were generated in the topmost layer and that both structures were terminated with zigzag edges. The formation of the Mo oxide layer at the interface demonstrates that O2 diffuses efficiently through the van der Waals (vdW) gap but not MoO3, which would otherwise sublime. The fact that TOs are several times larger than TEs indicates that oxidation is greatly enhanced when MoS2 is in direct contact with silica substrates, which suggests a catalytic effect. This study indicates that the vdW-bonded interfaces are essentially open to mass transport and can serve as a model system for investigating chemistry in low dimensional spaces.
قيم البحث
اقرأ أيضاً
Chemical transformation of existing two-dimensional (2D) materials can be crucial in further expanding the 2D crystal palette required to realize various functional heterostructures. In this work, we demonstrate a 2D on-stack chemical conversion of s
ingle-layer crystalline MoS2 into MoO3 with a precise layer control that enables truly 2D MoO3 and MoO3/MoS2 heterostructures. To minimize perturbation of the 2D morphology, a nonthermal oxidation using O2 plasma was employed. The early stage of the reaction was characterized by a defect-induced Raman peak, drastic quenching of photoluminescence (PL) signals and sub-nm protrusions in atomic force microscopy images. As the reaction proceeded from the uppermost layer to the buried layers, PL and optical second harmonic generation signals showed characteristic modulations revealing a layer-by-layer conversion. The plasma-generated 2D oxides, confirmed as MoO3 by x-ray photoelectron spectroscopy, were found to be amorphous but extremely flat with a surface roughness of 0.18 nm, comparable to that of 1L MoS2. The rate of oxidation quantified by Raman spectroscopy decreased very rapidly for buried sulfide layers due to protection by the surface 2D oxides, exhibiting a pseudo-self-limiting behavior. As exemplified in this work, various on-stack chemical transformations can be applied to other 2D materials in forming otherwise unobtainable materials and complex heterostructures, thus expanding the palette of 2D material building blocks.
Understanding the microscopic mechanism of chemical vapor deposition (CVD) growth of two-dimensional molybdenum disulfide (2D MoS2) is a fundamental issue towards the function-oriented controlled growth. In this work, we report results on revealing t
he growth kinetics of 2D MoS2 via capturing the nucleation seed, evolution morphology, edge structure and terminations at the atomic scale during CVD growth using the transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) studies. The direct growth of few- and mono-layer MoS2 onto graphene based TEM grids allow us to perform the subsequent TEM characterization without any solution-based transfer. Two forms of seeding centers are observed during characterizations: (i) Mo-oxysulfide (MoOxS2-y) nanoparticles either in multi-shelled fullerene-like structures or in compact nanocrystals for the growth of fewer-layer MoS2; (ii) Mo-S atomic clusters in case of monolayer MoS2. In particular, for the monolayer case, at the early stage growth, the morphology appears in irregular polygon shape comprised with two primary edge terminations: S-Mo Klein edge and Mo zigzag edge, approximately in equal numbers, while as the growth proceeds, the morphology further evolves into near-triangle shape in which Mo zigzag edge predominates. Results from density-functional theory calculations are also consistent with the inferred growth kinetics, and thus supportive to the growth mechanism we proposed. In general, the growth mechanisms found here should also be applicable in other 2D materials, such as MoSe2, WS2 and WSe2 etc.
Self-limiting oxidation of nanowires has been previously described as a reaction- or diffusion-controlled process. In this letter, the concept of finite reactive region is introduced into a diffusion-controlled model, based upon which a two-dimension
al cylindrical kinetics model is developed for the oxidation of silicon nanowires and is extended for tungsten. In the model, diffusivity is affected by the expansive oxidation reaction induced stress. The dependency of the oxidation upon curvature and temperature is modeled. Good agreement between the model predictions and available experimental data is obtained. The developed model serves to quantify the oxidation in two-dimensional nanostructures and is expected to facilitate their fabrication via thermal oxidation techniques. https://doi.org/10.1016/j.taml.2016.08.002
Structural, interfacial, optical, and transport properties of large-area MoS2 ultra-thin films on BN-buffered silicon substrates fabricated using magnetron sputtering are investigated. A relatively simple growth strategy is demonstrated here that sim
ultaneously promotes superior interfacial and bulk MoS2 properties. Few layers of MoS2 are established using X-ray reflectivity, diffraction, ellipsometry, and Raman spectroscopy measurements. Layer-specific modeling of optical constants shows very good agreement with first-principles calculations. Conductivity measurements reveal that few-layer MoS2 films are more conducting than many-layer films. Photo-conductivity measurements reveal that the sputter deposited MoS2 films compare favorably with other large-area methods. Our work illustrates that sputtering is a viable route for large-area device applications using transition metal dichalcogenides.
We extend the doubly degenerate Cahn-Hilliard (DDCH) models for isotropic surface diffusion, which yield more accurate approximations than classical degenerate Cahn-Hilliard (DCH) models, to the anisotropic case. We consider both weak and strong anis
otropies and demonstrate the capabilities of the approach for these cases numerically. The proposed model provides a variational and energy dissipative approach for anisotropic surface diffusion, enabling large scale simulations with material-specific parameters.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
