ترغب بنشر مسار تعليمي؟ اضغط هنا

Successful production of Solution Blow Spun YBCO+Ag complex ceramics

58   0   0.0 ( 0 )
 نشر من قبل Rafael Zadorosny
 تاريخ النشر 2020
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

YBCO fabrics composed of nanowires, produced by solution blow spinning (SBS) are so brittle that the Lorentz force produced by induced currents can be strong enough to damage them. On the other hand, it is known that silver addition improves the mechanical and flux pinning properties of ceramic superconductors. Thus, in this work, we show how we successfully obtained a polymeric precursor solution containing YBCO$+$Ag salts, which can be spun by the SBS route to produce ceramic samples. Yttrium, barium, copper, and silver metal acetates, and polyvinylpyrrolidone (PVP) (in a ratio of 5:1wt [PVP:acetates]) were dissolved in a solution with 61.5 wt% of methanol, 12 wt% of propionic acid, and 26.5 wt% of ammonium hydroxide, together with 6 wt% of PVP in solution. Three different amounts of silver (10 wt%, 20 wt%, and 30 wt%) were used in YBa$_2$Cu$_3$O$_{7-x}$. The TGA characterizations revealed a lowering of crystallization and partial melting temperatures by about SI{30}{celsius}. SEM images show that after burning out the polymer, a fabric composed of nanowires of diameters up to SI{380}{ ano metre} is produced. However, after the sintering process at SI{925}{celsius} for SI{1}{hour}, the nanowires shrink into a porous-like sample.



قيم البحث

اقرأ أيضاً

Titanium diboride (TiB2) is a low-density refractory material belonging to the family of ultra-high temperature ceramics (UHTCs). This paper reports on the production and microstructural and optical characterization of nearly fully dense TiB2, with p articular interest to its potential utilization as novel thermal solar absorber. Monolithic bulk samples are produced starting from elemental reactants by a two-step method consisting of the Self-propagating High-temperature Synthesis (SHS) followed by the Spark Plasma Sintering (SPS) of the resulting powders. The surface of obtained samples has-been characterized from the microstructural and topological points of view. The hemispherical reflectance spectrum has been measured from 0.3 to 15 um wavelength, to evaluate the potential of this material as solar absorber for future concentrating solar plants.
Carbon Nanotubes (CNTs) of sufficiently large diameter and a few layers self-collapse into flat ribbons at atmospheric pressure, forming bundles of stacked CNTs that maximize packing and thus CNT interaction. Their improved stress transfer by shear m akes collapsed CNTs ideal building blocks in macroscopic fibers of CNTs with high-performance longitudinal properties, particularly high tensile properties as reinforcing fibres. This work introduces cross-sectional transmission electron microscopy of FIB-milled samples as a way to univocally identify collapsed CNTs and to determine the full population of different CNTs in macroscopic fibers produced by spinning from floating catalyst chemical vapour deposition. We show that close proximity in bundles is a major driver for collapse and that CNT stoutness (number of layers/diameter), which dominates the collapse onset, is controlled by the growth promotor. Despite differences in decomposition route, different C precursors lead to similar distributions of the ratio layers/diameter. The synthesis conditions in this study give a maximum fraction of collapsed CNTs of 70$%$ when using selenium as promotor, corresponding to an average of $0.25 layer/nm$.
Complex oxide thin films and heterostructures exhibit a profusion of exotic phenomena, often resulting from the intricate interplay between film and substrate. Recently it has become possible to isolate epitaxially grown single-crystalline layers of these materials, enabling the study of their properties in the absence of interface effects. In this work, we create ultrathin membranes of strongly correlated materials and demonstrate top-down fabrication of nanomechanical resonators made out of ce{SrTiO3} and ce{SrRuO3}. Using laser interferometry, we successfully actuate and measure the motion of the nanodrum resonators. By measuring their temperature-dependent mechanical response, we observe signatures of structural phase transitions in ce{SrTiO3}, which affect the strain and mechanical dissipation in the resonators. This approach can be extended to investigate phase transitions in a wide range of materials. Our study demonstrates the feasibility of integrating ultrathin complex oxide membranes for realizing nanoelectromechanical systems on arbitrary substrates.
An YBCO-based test structure corresponding to the family of ReRAM devices associated with the valence change mechanism is presented. We have characterized its electrical response previous to its lift-off to a Low Earth Orbit (LEO) using standard elec tronics and also with the dedicated LabOSat-01 controller. Similar results were obtained in both cases. After about 200 days at LEO on board a small satellite, electrical tests started on the memory device using the LabOSat-01 controller. We discuss the results of the first 150 tests, performed along a 433-day time interval in space. The memory device remained operational despite the hostile conditions that involved launching, lift-off vibrations, permanent thermal cycling and exposure to ionizing radiation, with doses 3 orders of magnitude greater than the usual ones on Earth. The device showed resistive switching and IV characteristics similar to those measured on Earth, although with changes that follow a smooth drift in time. A detailed study of the electrical transport mechanisms, based on previous models that indicate the existence of various conducting mechanisms through the metal-YBCO interface showed that the observed drift can be associated with a local temperature drift at the LabOSat controller, with no clear evidence that allows determining changes in the underlying microscopic factors. These results show the reliability of complex-oxide non-volatile ReRAM-based devices in order to operate under all the hostile conditions encountered in space-borne applications.
Main focus of this study is the investigation of thermodynamics phenomena responsible for the High Field Q Slope (HFQS) in SRF cavities by Internal Friction (IF) measurement. Mechanical spectroscopy is, indeed, a well-established technique to study p recipitate formations in BCC materials and several works on the effects of impurities as N and O on the Snoek peak have been published so far and will be taken as reference to explain the mechanisms behind the observed dissipation effects. Internal Friction measurements were performed in Belgium at IMCE on Nb rectangular shape samples with different RRR values prepared at Fermilab by using Electro Polishing (EP), N-doping and heat treatments in order to reproduce the same conditions during the standard treatments applied on bulk Nb SRF cavities. From IF spectra, the H trapping mechanism by interstitial atoms (N and O and/or vacancies, depending on the purity level, RRR) can be easily recognized leading to results that perfectly corroborate previous findings on Q-disease, HFQS and RRR phenomena.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا