اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThe Simulation, Fabrication Technology and Characteristic Research of Micro-Pressure Sensor with Isosceles Trapezoidal Beam-Membrane
66
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
A micro-pressure sensor with an isosceles trapezoidal beam-membrane (ITBM) is proposed in this paper, consisting of a square silicon membrane, four isosceles trapezoidal beams and four piezoresistors.To investigate how the elastic silicon membrane affects pressure sensitive characteristics, a simulation models based on ANSYS 15.0 software were used to analyze the effect of structural dimension on characteristics of pressure sensor. According to that, the chips of micro-pressure sensors were fabricated by micro-electro-mechanical system (MEMS) technology on a silicon wafer with <100> orientation.The experimental results show that the proposed sensor achieves a better sensitivity of 9.64 mV/kPa and an excellent linearity of 0.09%F.S. in the range of 0~3.0 kPa at room temperature and a supply voltage of 5.0 V,with a super temperature coefficient of sensitivity(TCS) about - 684 ppm/K from 235.15 K to 360.15 K and low pressure measurement less than 3.0 kPa.
قيم البحث
اقرأ أيضاً
Micro-fabrication in diamond is involved in a wide set of emerging technologies, exploiting the exceptional characteristics of diamond for application in bio-physics, photonics, radiation detection. Micro ion-beam irradiation and pulsed laser irradia
tion are complementary techniques, which permit the implementation of complex geometries, by modification and functionalization of surface and/or bulk material, modifying the optical, electrical and mechanical characteristics of the material. In this article we summarize the work done in Florence (Italy) concerning ion beam and pulsed laser beam micro-fabrication in diamond.
We realize squeeze film pressure sensors using suspended, high mechanical quality silicon nitride membranes forming few-micron gap sandwiches. The effects of air pressure on the mechanical vibrations of the membranes are investigated in the range 10^
-3-50 mbar and the intermembrane coupling induced by the gas is discussed in light of a squeeze film coupled-oscillator model. The high responsivity (several kHz/mbar) and the sub-pascal sensitivity of such simple pressure sensors are attractive for absolute and direct pressure measurements in rarefied air or high vacuum environments.
The high flexibility, impermeability and strength of graphene membranes are key properties that can enable the next generation of nanomechanical sensors. However, for capacitive pressure sensors the sensitivity offered by a single suspended graphene
membrane is too small to compete with commercial sensors. Here, we realize highly sensitive capacitive pressure sensors consisting of arrays of nearly ten thousand small, freestanding double-layer graphene membranes. We fabricate large arrays of small diameter membranes using a procedure that maintains the superior material and mechanical properties of graphene, even after high-temperature anneals. These sensors are readout using a low cost battery-powered circuit board, with a responsivity of up to 47.8 aF Pa$^{-1}$ mm$^{-2}$, thereby outperforming commercial sensors.
Incorporating accurate physics-based simulation into interactive design tools is challenging. However, adding the physics accurately becomes crucial to several emerging technologies. For example, in virtual/augmented reality (VR/AR) videos, the faith
ful reproduction of surrounding audios is required to bring the immersion to the next level. Similarly, as personal fabrication is made possible with accessible 3D printers, more intuitive tools that respect the physical constraints can help artists to prototype designs. One main hurdle is the sheer amount of computation complexity to accurately reproduce the real-world phenomena through physics-based simulation. In my thesis research, I develop interactive tools that implement efficient physics-based simulation algorithms for automatic optimization and intuitive user interaction.
Future quantum technology relies crucially on building quantum networks with high fidelity. To achieve this challenging goal, it is of utmost importance to connect single quantum systems in a way such that their emitted single-photons overlap with th
e highest possible degree of coherence. This requires perfect mode overlap of the emitted light of different emitters, which necessitates the use of single mode fibers. Here we present an advanced manufacturing approach to accomplish this task: we combine 3D printed complex micro-optics such as hemispherical and Weierstrass solid immersion lenses as well as total internal reflection solid immersion lenses on top of single InAs quantum dots with 3D printed optics on single mode fibers and compare their key features. Interestingly, the use of hemispherical solid immersion lenses further increases the localization accuracy of the emitters to below 1 nm when acquiring micro-photoluminescence maps. The system can be joined together and permanently fixed. This integrated system can be cooled by dipping into liquid helium, by a Stirling cryocooler or by a closed-cycle helium cryostat without the necessity for optical windows, as all access is through the integrated single mode fiber. We identify the ideal optical designs and present experiments that prove excellent high-rate single-photon emission by high-contrast Hanbury Brown and Twiss experiments.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
