اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدDesign and evaluation of conjugated polymers with polar side chains as electrode materials for electrochemical energy storage in aqueous electrolytes
63
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We report the development of redox-active conjugated polymers with potential application to electrochemical energy storage. Side chain engineering enables processing of the polymer electrodes from solution, stability in aqueous electrolytes and efficient transport of ionic and electronic charge carriers. We synthesized a 3,3 dialkoxybithiophene homo polymer (p type polymer) with glycol side chains and prepared naphthalene 1,4,5,8-tetracarboxylic-diimide-dialkoxybithiophene (NDI gT2) copolymers (n type polymer) with either a glycol or zwitterionic side chain on the NDI unit. For the latter, we developed a post-functionalization synthesis to attach the polar zwitterion side chains to the polymer backbone to avoid challenges of purifying polar intermediates. We demonstrate fast and reversible charging of solution processed electrodes for both the p- and n type polymers in aqueous electrolytes, without using additives or porous scaffolds and for films up to micrometers thick. We apply spectroelectrochemistry as an in operando technique to probe the state of charge of the electrodes. This reveals that thin films of the p-type polymer and zwitterion n-type polymer can be charged reversibly with up to two electronic charges per repeat unit (bipolaron formation). We combine thin films of these polymers in a two-electrode cell and demonstrate output voltages of up to 1.4 V with high redox stability. Our findings demonstrate the potential of functionalizing conjugated polymers with appropriate polar side chains to improve specific capacity, reversibility and rate capabilities of polymer electrodes in aqueous electrolytes.
قيم البحث
اقرأ أيضاً
Two-dimensional carbides and nitrides of transition metals, known as MXenes, are a fast-growing family of 2D materials that draw attention as energy storage materials. So far, MXenes are mainly prepared from Al-containing MAX phases (where A = Al) by
Al dissolution in F-containing solution, but most other MAX phases have not been explored. Here, a redox-controlled A-site-etching of MAX phases in Lewis acidic melts is proposed and validated by the synthesis of various MXenes from unconventional MAX phase precursors with A elements Si, Zn, and Ga. A negative electrode of Ti3C2 MXene material obtained through this molten salt synthesis method delivers a Li+ storage capacity up to 738 C g-1 (205 mAh g-1) with high-rate performance and pseudocapacitive-like electrochemical signature in 1M LiPF6 carbonate-based electrolyte. MXene prepared from this molten salt synthesis route offer opportunities as high-rate negative electrode material for electrochemical energy storage applications.
Galvanostatic Intermittent Titration Technique (GITT) is widely used to evaluate solid-state diffusion coefficients in electrochemical systems. However, the existing analysis methods for GITT data require numerous assumptions, and the derived diffusi
on coefficients typically are not independently validated. To investigate the validity of the assumptions and derived diffusion coefficients, we employ a direct pulse fitting method for interpreting GITT data that involves numerically fitting an electrochemical pulse and subsequent relaxation to a one-dimensional, single-particle, electrochemical model coupled with non-ideal transport to directly evaluate diffusion coefficients that are independently verified through cycling predictions. Extracted from GITT measurements of the intercalation regime of FeS2 and used to predict the discharge behavior, our non-ideal diffusion coefficients prove to be two orders of magnitude more accurate than ideal diffusion coefficients extracted using conventional methods. We further extend our model to a polydisperse set of particles to show the validity of a single-particle approach when the modeled radius is proportional to the total volume-to-surface-area ratio of the system.
Upon insertion and extraction of lithium, materials important for electrochemical energy storage can undergo changes in thermal conductivity (${Lambda}$) and elastic modulus ($it M$). These changes are attributed to evolution of the intrinsic thermal
carrier lifetime and interatomic bonding strength associated with structural transitions of electrode materials with varying degrees of reversibility. Using in situ time-domain thermoreflectance (TDTR) and picosecond acoustics, we systemically study $Lambda$ and $it M$ of conversion, intercalation and alloying electrode materials during cycling. The intercalation V$_{2}$O$_{5}$ and TiO$_{2}$ exhibit non-monotonic reversible ${Lambda}$ and $it M$ switching up to a factor of 1.8 (${Lambda}$) and 1.5 ($it M$) as a function of lithium content. The conversion Fe$_{2}$O$_{3}$ and NiO undergo irreversible decays in ${Lambda}$ and $it M$ upon the first lithiation. The alloying Sb shows the largest and partially reversible order of the magnitude switching in ${Lambda}$ between the delithiated (18 W m$^{-1}$ K$^{-1}$) and lithiated states (<1 W m$^{-1}$ K$^{-1}$). The irreversible ${Lambda}$ is attributed to structural degradation and pulverization resulting from substantial volume changes during cycling. These findings provide new understandings of the thermal and mechanical property evolution of electrode materials during cycling of importance for battery design, and also point to pathways for forming materials with thermally switchable properties.
The performance of gold nanoparticles (NPs) in applications depends critically on the structure of the NP-solvent interface, at which the electrostatic surface polarization is one of the key characteristics that affects hydration, ionic adsorption, a
nd electrochemical reactions. Here, we demonstrate significant effects of explicit metal polarizability on the solvation and electrostatic properties of bare gold NPs in aqueous electrolyte solutions of sodium salts of various anions (Cl$^-$, BF$_4$$^-$, PF$_6$$^-$, Nip$^-$(nitrophenolate), and 3- and 4-valent hexacyanoferrate (HCF)), using classical molecular dynamics simulations with a polarizable core-shell model of the gold atoms. We find considerable spatial heterogeneity of the polarization and electrostatic potentials on the NP surface, mediated by a highly facet-dependent structuring of the interfacial water molecules. Moreover, ion-specific, facet-dependent ion adsorption leads to large alterations of the interfacial polarization. Compared to non-polarizable NPs, polarizability modifies water local dipole densities only slightly, but has substantial effects on the electrostatic surface potentials, and leads to significant lateral redistributions of ions on the NP surface. Besides, interfacial polarization effects on the individual monovalent ions cancel out in the far field, and effective Debye-Huckel surface potentials remain essentially unaffected, as anticipated from continuum `image-charge concepts. Hence, the explicit charge response of metal NPs is crucial for the accurate description and interpretation of interfacial electrostatics (as, e.g., for charge transfer and interface polarization in catalysis and electrochemistry).
Energy demands of modern society require efficient means of energy conversion and storage. Nanocarbons have been identified as versatile materials which combine many desirable properties, allowing them to be used in electrochemical power sources, fro
m electrochemical capacitors to fuel cells. Efficient production of nanocarbons requires innovative and scalable approaches which allow for tuning of their physical and chemical properties. Carbonization of polymeric nanostructures has been demonstrated as a promising approach for production of high-performance nanocarbons with desired morphology and variable surface chemical properties. These materials have been successfully used as active electrode materials in electrochemical capacitors, as electrocatalysts or catalyst supports. Moreover, these materials are often found as parts of composite electrode materials where they play very important role in boosting materials performance. In this contribution we shall review developments in the field of application of polymer-derived nanocarbons for electrochemical energy conversion and storage applications, covering the last decade. Primary focus will be on polyaniline and polypyrrole but carbons derived from other polymers will also be mentioned. We shall emphasize the link between the physical and chemical properties of nanocarbons and their performance in electrochemical power sources with an attempt to derive general guidelines for further development of new materials with improved performances.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
