اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدKinetic Similarity between Extinction Strain Rate and Laminar Flame Speed
75
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Extinction strain rate (ESR) and laminar flame speed (LFS) are fundamental properties of a fuel/air mixture that are often utilized as scaling parameters in turbulent combustion. While LFS at atmospheric and elevated pressures are extensively investigated, experimental measurements of ESR with counterflow premixed flames are very limited for flame instability often occurs near extinction, especially at high pressures. Due to the scarcity of ESR measurements, most combustion kinetic models are mainly validated and optimized against LFS. However, it is questionable whether the controlling reactions are the same for ESR and LFS such that those models are also valid for predicting ESR. This work quantifies the kinetic similarities between ESR and LFS by analyzing their kinetic sensitivity directions. The direction is represented by a unit vector composed of the normalized sensitivity of ESR or LFS to the rate constant for each elemental reaction. Consequently, the similarity between the two directions is measured by the inner product of the corresponding unit vectors. The sensitivity directions of ESR and LFS are found parallel for various fuels, equivalence ratios, and pressures. Furthermore, sensitivity directions at various strain rates are also similar for the maximum temperature, local temperature at various locations in the flame coordinate, and ESR in counterflow premixed flames. These findings suggest that LFS and ESR are similarly effective as the target for constraining and optimizing rate constants in kinetic models. In addition, the independence of the sensitivity directions on the strain rate also enables us to perform uncertainty quantification for turbulent flames with a wide range of strain rates based on the kinetic sensitivity of ESR and LFS.
قيم البحث
اقرأ أيضاً
We study the effect of thermal noise on the propagation speed of a planar flame. We show that this out of equilibrium greatly amplifies the effect of thermal noise to yield macroscopic reductions in the flame speed over what is predicted by the noise
-free model. Computations show that noise slows the flame significantly. The flame is modeled using Navier Stokes equations with appropriate diffusive transport terms and chemical kinetic mechanism of hydrogen/oxygen. Thermal noise is modeled within the continuum framework using a system of stochastic partial differential equations, with transport noise from fluctuating hydrodynamics and reaction noise from a poisson model. We use a full chemical kinetics model in order to get quantitatively meaningful results. We compute steady and dynamic flames using an operator split finite volume scheme. New characteristic boundary conditions avoid non-physical boundary layers at computational boundaries. New limiters prevent stochastic terms from introducing non-physical negative concentrations. This represents the first computation of a model with thermal noise is a system with this degree of physical detail.
This paper presents a flame-height correlation for laminar to transition-to-turbulent regime diffusion flames. Flame-height measurements are obtained by means of numerical and experimental studies in which three high definition cameras were employed
to take frontal, lateral and 45{deg} angled images simultaneously. The images were analysed using an image-processing algorithm to determine the flame-height through indirect measurement. To locate an overall chemical-flame-length, numerical simulations were conducted with the unsteady Reynolds-Averaged Navier-Stokes technique. The eddy-dissipation model was also implemented to calculate chemical reaction rate. The experiments show that this proposed correlation has an adjustment variation of luminous flame-height for the laminar regime of 16.9%, which indicates that, without the use of the intermittent buoyant flame-height correlation, it globally best represents the flame-height in this regime. For the laminar and transition-to-turbulence regime the adjustment variations are 5.54% compared to the most accepted flame-height correlations, thus providing an acceptably good fitting. The numerical results show that the proposed range for the chemical-flame-length is located between the luminous and flickering flame zone compared to the experimental flame images. These results agree with the chemical length zone reported in the literature. Therefore, the correlation can be used for laminar and transition-to-turbulent combustion regimes.
We investigate the capability of neural network-based model order reduction, i.e., autoencoder (AE), for fluid flows. As an example model, an AE which comprises of a convolutional neural network and multi-layer perceptrons is considered in this study
. The AE model is assessed with four canonical fluid flows, namely: (1) two-dimensional cylinder wake, (2) its transient process, (3) NOAA sea surface temperature, and (4) $y-z$ sectional field of turbulent channel flow, in terms of a number of latent modes, a choice of nonlinear activation functions, and a number of weights contained in the AE model. We find that the AE models are sensitive against the choice of the aforementioned parameters depending on the target flows. Finally, we foresee the extensional applications and perspectives of machine learning based order reduction for numerical and experimental studies in fluid dynamics community.
A series of Direct Numerical Simulations (DNS) of lean methane/air flames was conducted in order to investigate the enhancement of the turbulent flame speed and modifications to the reaction layer structure associated with the systematic increase of
the integral scale of turbulence $l$ while the Karlovitz number and the Kolmogorov scale are kept constant. Four turbulent slot jet flames are simulated at increasing Reynolds number and up to $Re approx 22000$, defined based on the bulk velocity, slot width, and the reactants properties. The turbulent flame speed $S_T$ is evaluated locally at select streamwise locations and it is observed to increase both in the streamwise direction for each flame and across flames for increasing Reynolds number, in line with a corresponding increase of the turbulent integral scale. In particular, the turbulent flame speed $S_T$ increases exponentially with the integral scale for $l$ up to about 6 laminar flame thicknesses, while the scaling becomes a power-law for larger values of $l$. These trends cannot be ascribed completely to the increase in the flame surface, since the turbulent flame speed looses its proportionality to the flame area as the integral scale increases; in particular, it is found that the ratio of turbulent flame speed to area attains a power-law scaling $l^{0.2}$. This is caused by an overall broadening of the reaction layer for increasing integral scale, which is not associated with a corresponding decrease of the reaction rate, causing a net enhancement of the overall burning rate. This observation is significant since it suggests that a continuous increase in the size of the largest scales of turbulence might be responsible for progressively stronger modifications of the flames inner layers even if the smallest scales, i.e., the Karlovitz number, are kept constant.
The movement of subaqueous sediment in laminar shearing flow is numerically investigated by the coupled lattice Boltzmann and discrete element methods. First, the numerical method is validated by comparing the phase diagram proposed by Ouriemi {it et
al.} ({it J. Fluid Mech}., vol. 636, 2009, pp. 321-336). Second, a detailed study on sediment movement is performed for sediment with varying solid volume fractions, and a nonlinear relationship between the normalised thickness of the mobile layer and the normalised fluid flow rate is observed for a densely-packed sediment. Third, an independent investigation on the effective viscosity and friction coefficient of the sediment under different fluid flow rates is conducted in a shear cell; and substitution of these two critical parameters into a theoretical expression proposed by Aussillous {it et al.} ({it J. Fluid Mech}., vol. 736, 2013, pp. 594-615) provides consistent predictions of bedload thickness with the simulation results of sediment movement. Therefore, we conclude that the non-Newtonian behaviour of densely-packed sediment leads to the nonlinear relationship between the normalised thickness of the mobile layer and the normalised fluid flow rate.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
