ترغب بنشر مسار تعليمي؟ اضغط هنا

Upper limit to the photovoltaic efficiency of imperfect crystals

70   0   0.0 ( 0 )
 نشر من قبل Sunghyun Kim
 تاريخ النشر 2019
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

The Shockley-Queisser (SQ) limit provides a convenient metric for predicting light-to-electricity conversion efficiency of a solar cell based on the band gap of the light-absorbing layer. In reality, few materials approach this radiative limit. We develop a formalism and a computational method to predict the maximum photovoltaic efficiency of imperfect crystals from first principles. Our scheme includes equilibrium populations of native defects, their carrier-capture coefficients, and the associated recombination rates. When applied to kesterite solar cells, we reveal an intrinsic limit of 20% for $mathrm{Cu_2ZnSnSe_4}$, which falls far below the SQ limit of 32%. The effects of atomic substitution and extrinsic doping are studied, leading to pathways for enhanced efficiency of 31%. This approach can be applied to support targeted-materials selection for future solar-energy technologies.



قيم البحث

اقرأ أيضاً

345 - Sunghyun Kim , Aron Walsh 2021
The thermodynamic limit of photovoltaic efficiency for a single-junction solar cell can be readily predicted using the bandgap of the active light absorbing material. Such an approach overlooks the energy loss due to non-radiative electron-hole proce sses. We propose a practical ab initio procedure to determine the maximum efficiency of a thin-film solar cell that takes into account both radiative and non-radiative recombination. The required input includes the frequency-dependent optical absorption coefficient, as well as the capture cross-sections and equilibrium populations of point defects. For kesterite-structured Cu$_2$ZnSnS$_4$, the radiative limit is reached for a film thickness of around 2.6 micrometer, where the efficiency gain due to light absorption is counterbalanced by losses due to the increase in recombination current.
Recent calculations using coupled cluster on solids have raised discussion of using a $N^{-1/3}$ power law to fit the correlation energy when extrapolating to the thermodynamic limit, an approach which differs from the more commonly used $N^{-1}$ pow er law which is (for example) often used by quantum Monte Carlo methods. In this paper, we present one way to reconcile these viewpoints. Coupled cluster doubles calculations were performed on uniform electron gases reaching system sizes of $922$ electrons for an extremely wide range of densities ($0.1<r_s<100.0$) to study how the correlation energy approaches the thermodynamic limit. The data were corrected for basis set incompleteness error and use a selected twist angle approach to mitigate finite size error from shell filling effects. Analyzing these data, we initially find that a power law of $N^{-1/3}$ appears to fit the data better than a $N^{-1}$ power law in the large system size limit. However, we provide an analysis of the transition structure factor showing that $N^{-1}$ still applies to large system sizes and that the apparent $N^{-1/3}$ power law occurs only at low $N$.
The linked cell list algorithm is an essential part of molecular simulation software, both molecular dynamics and Monte Carlo. Though it scales linearly with the number of particles, there has been a constant interest in increasing its efficiency, be cause a large part of CPU time is spent to identify the interacting particles. Several recent publications proposed improvements to the algorithm and investigated their efficiency by applying them to particular setups. In this publication we develop a general method to evaluate the efficiency of these algorithms, which is mostly independent of the parameters of the simulation, and test it for a number of linked cell list algorithms. We also propose a combination of linked cell reordering and interaction sorting that shows a good efficiency for a broad range of simulation setups.
Here we report the development of high-efficiency microscale GaAs laser power converters, and their successful transfer printing onto silicon substrates, presenting a unique, high power, low-cost and integrated power supply solution for implantable e lectronics, autonomous systems and internet of things applications. We present 300 {mu}m diameter single-junction GaAs laser power converters and successfully demonstrate the transfer printing of these devices to silicon using a PDMS stamp, achieving optical power conversion efficiencies of 48% and 49% under 35 and 71 W/cm2 808 nm laser illumination respectively. The transferred devices are coated with ITO to increase current spreading and are shown to be capable of handling very high short-circuit current densities up to 70 A/cm2 under 141 W/cm2 illumination intensity (~1400 Suns), while their open circuit voltage reaches 1235 mV, exceeding the values of pre-transfer devices indicating the presence of photon-recycling. These optical power sources could deliver Watts of power to sensors and systems in locations where wired power is not an option, while using a massively parallel, scalable, and low-cost fabrication method for the integration of dissimilar materials and devices.
101 - Zekun Ren , Juhwan Noh , Siyu Tian 2020
Deep learning has fostered many novel applications in materials informatics. However, the inverse design of inorganic crystals, $textit{i.e.}$ generating new crystal structure with targeted properties, remains a grand challenge. An important ingredie nt for such generative models is an invertible representation that accesses the full periodic table. This is challenging due to limited data availability and the complexity of 3D periodic crystal structures. In this paper, we present a generalized invertible representation that encodes the crystallographic information into the descriptors in both real space and reciprocal space. Combining with a generative variational autoencoder (VAE), a wide range of crystallographic structures and chemistries with desired properties can be inverse-designed. We show that our VAE model predicts novel crystal structures that do not exist in the training and test database (Materials Project) with targeted formation energies and band gaps. We validate those predicted crystals by first-principles calculations. Finally, to design solids with practical applications, we address the sparse label problem by building a semi-supervised VAE and demonstrate its successful prediction of unique thermoelectric materials
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا