اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدAqueous metal-organic solutions for YSZ thin film inkjet deposition
67
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Inkjet printing of 8% Y2O3-stabilized ZrO2 (YSZ) thin films is achieved by designing a novel water-based reactive ink for Drop-on-Demand (DoD) inkjet printing. The ink formulation is based on a novel chemical strategy that consists of a combination of metal oxide precursors (zirconium alkoxide and yttrium salt), water and a nucleophilic agent, i.e. n-methyldiethanolamine (MDEA). This chemistry leads to metal-organic complexes with long term ink stability and high precision printability. Ink rheology and chemical reactivity are analyzed and controlled in terms of metal-organic interactions in the solutions. Thin dense nanocrystalline YSZ film below 150 nm are obtained by low temperature calcination treatments (400-500 {deg}C), making the deposition suitable for a large variety of substrates, including silicon, glass and metals. Thin films and printed patterns achieve full densification with no lateral shrinkage and high ionic conductivity.
قيم البحث
اقرأ أيضاً
Kapton HN films, adopted worldwide due to their superior thermal durability (up to 400 {deg}C), allow the high temperature sintering of nanoparticle based metal inks. By carefully selecting inks and Kapton substrates, outstanding thermal stability an
d anti-delaminating features are obtained in both aqueous and organic solutions and were applied to four novel devices: a solid state ion selective nitrate sensor, an ssDNA based mercury aptasensor, a low cost protein sensor, and a long lasting organic thin film transistor (OTFT). Many experimental studies on parameter combinations were conducted during the development of the above devices. The results showed that the ion selective nitrate sensor displayed a linear sensitivity range with a limit of detection of 2 ppm. The mercury sensor exhibited a linear correlation between the RCT values and the increasing concentrations of mercury. The protein printed circuit board (PCB) sensor provided a much simpler method of protein detection. Finally, the OTFT demonstrated a stable performance with mobility values for the linear and saturation regimes, and the threshold voltage. These devices have shown their value and reveal possibilities that could be pursued.
Molecular dynamics simulations combined with periodic electronic structure calculations are performed to decipher structural, thermodynamical and dynamical properties of the interfaced vs. confined water adsorbed in hexagonal 1D channels of the 2D la
yered electrically conductive Cu3(HHTP)2 and Cu3(HTTP)2 metal-organic frameworks (HHTP=2,3,6,7,10,11-hexahydroxytriphenylene and HTTP = 2,3,6,7,10,11-hexathiotriphenylene). Comparing water adsorption in bulk vs. slab models of the studied 2D MOFs shows that water is preferentially adsorbed on the framework walls via forming hydrogen bonds to the organic linkers rather than by coordinating to the coordinatively unsaturated open-Cu2+ sites. Theory predicts that in Cu3(HTTP)2 the van der Waals interactions are stronger which helps the MOF maintain its layered morphology with allowing very little water molecules to diffuse into the interlayer space. Data presented in this work are general and helpful in implementing new strategies for preserving the integrity as well as electrical conductivity of porous materials in aqueous solutions.
Low-dimensional boundaries between phases and domains in organic thin films are important in charge transport and recombination. Here, fluctuations of interfacial boundaries in an organic thin film, acridine-9-carboxylic acid (ACA) on Ag(111), have b
een visualized in real time, and measured quantitatively, using Scanning Tunneling Microscopy. The boundaries fluctuate via molecular exchange with exchange time constants of 10-30 ms at room temperature, yielding length mode fluctuations that should yield characteristic f-1/2 signatures for frequencies less than ~100 Hz. Although ACA has highly anisotropic intermolecular interactions, it forms islands that are compact in shape with crystallographically distinct boundaries that have essentially identical thermodynamic and kinetic properties . The physical basis of the modified symmetry is shown to arise from significantly different substrate interactions induced by alternating orientations of successive molecules in the condensed phase. Incorporating this additional set of interactions in a lattice gas model leads to effective multi-component behavior, as in the Blume-Emery-Griffiths (BEG) model, and can straightforwardly reproduce the experimentally observed isotropic behavior. The general multi-component description allows the domain shapes and boundary fluctuations to be tuned from isotropic to highly anisotropic in terms of the balance between intermolecular interactions and molecule-substrate interactions. Key words: Organic thin film, fluctuations, STM, molecular interactions, diffusion kinetics, phase coexistence
Discovering and optimizing commercially viable materials for clean energy applications typically takes over a decade. Self-driving laboratories that iteratively design, execute, and learn from material science experiments in a fully autonomous loop p
resent an opportunity to accelerate this research. We report here a modular robotic platform driven by a model-based optimization algorithm capable of autonomously optimizing the optical and electronic properties of thin-film materials by modifying the film composition and processing conditions. We demonstrate this platform by using it to maximize the hole mobility of organic hole transport materials commonly used in perovskite solar cells and consumer electronics. This demonstration highlights the possibilities of using autonomous laboratories to discover organic and inorganic materials relevant to materials sciences and clean energy technologies.
The performance of solution-processed solar cells strongly depends on the geometrical structure and roughness of the photovoltaic layers formed during film drying. During the drying process, the interplay of crystallization and liquid-liquid demixing
leads to the structure formation on the nano- and microscale and to the final rough film. In order to better understand how the film structure can be improved by process engineering, we aim at theoretically investigating these systems by means of phase-field simulations. We introduce an evaporation model based on the Cahn-Hilliard equation for the evolution of the fluid concentrations coupled to the Allen-Cahn equation for the liquid-vapour phase transformation. We demonstrate its ability to match the experimentally measured drying kinetics and study the impact of the parameters of our model. Furthermore, the evaporation of solvent blends and solvent-vapour annealing are investigated. The dry film roughness emerges naturally from our set of equations, as illustrated through preliminary simulations of spinodal decomposition and film drying on structured substrates.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
