اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدChemically Induced Transformation of CVD-Grown Bilayer Graphene into Single Layer Diamond
120
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Notwithstanding numerous density functional studies on the chemically induced transformation of multilayer graphene into a diamond-like film, a comprehensive convincing experimental proof of such a conversion is still lacking. We show that the fluorination of graphene sheets in Bernal (AB)-stacked bilayer graphene (AB-BLG) grown by chemical vapor deposition on a single crystal CuNi(111) surface triggers the formation of interlayer carbon-carbon bonds, resulting in a fluorinated diamond monolayer (F-diamane). Induced by fluorine chemisorption, the phase transition from AB-BLG to single layer diamond was studied and verified by X-ray photoelectron, ultraviolet photoelectron, Raman, UV-Vis, electron energy loss spectroscopies, transmission electron microscopy, and DFT calculations.
قيم البحث
اقرأ أيضاً
Conversion of pure spin current to charge current in single-layer graphene (SLG) is investigated by using spin pumping. Large-area SLG grown by chemical vapor deposition is used for the conversion. Efficient spin accumulation in SLG by spin pumping e
nables observing an electromotive force produced by the inverse spin Hall effect (ISHE) of SLG. The spin Hall angle of SLG is estimated to be 6.1*10-7. The observed ISHE in SLG is ascribed to its non-negligible spin-orbit interaction in SLG.
The conversion of graphene into diamond is a new way for preparing ultrathin diamond film without pressure. Herein, we investigated the transformation mechanism of surface-hydrogenated bilayer graphene (SHBG) into surface-hydrogenated single-layer di
amond (SHSLD) crystal, inserting fifteen kinds of single metal atoms without any pressure, by using the systematical first-principles calculations. Compared with the configuration without metal atom, SHBG can be transformed into SHSLD spontaneously in thermodynamics under the action of single metal atom, and its formation energy can even decrease from 0.82 eV to -5.79 eV under the action of Hf atom. According to our results, the outer electron orbits and atomic radius of metal atom are two important factors that affect the conversion. For the phase transition to occur, the metal atom needs to have enough empty d orbitals, and the radius of the metal atom is in the range of 0.136-0.159 nm. Through further analysis, we find that the p orbitals of carbon atoms and d orbital of metal atom in SHBG will be strongly hybridized, thereby promoting the conversion. The results supply important significance to experimentally prepare diamond without pressure through hydrogenated graphene.
The transfer of graphene grown by chemical vapor deposition (CVD) using amorphous polymers represents a widely implemented method for graphene-based electronic device fabrication. However, the most commonly used polymer, poly(methyl methacrylate) (PM
MA), leaves a residue on the graphene that limits the mobility. Here we report a method for graphene transfer and patterning that employs a perfluoropolymer---Hyflon---as a transfer handle and to protect graphene against contamination from photoresists or other polymers. CVD-grown graphene transferred this way onto LaAlO$_3$/SrTiO$_3$ heterostructures is atomically clean, with high mobility (~30,000 cm$^2$V$^{-1}$s$^{-1}$) near the Dirac point at 2 K and clear, quantized Hall and magneto-resistance. Local control of the LaAlO$_3$/SrTiO$_3$ interfacial metal-insulator transition---through the graphene---is preserved with this transfer method. The use of perfluoropolymers such as Hyflon with CVD-grown graphene and other 2D materials can readily be implemented with other polymers or photoresists.
Thick CVD diamond layers were successfully grown on (113)-oriented substrates. They exhibited smooth surface morphologies and a crystalline quality comparable to (100) electronic grade material, and much better than (111)-grown layers. High growth ra
tes (15-50 {mu}m/h) were obtained while nitrogen doping could be achieved in a fairly wide range without seriously imparting crystalline quality. Electron spin resonance measurements were carried out to determine NV centers orientation and concluded that one specific orientation has an occurrence probability of 73 % when (100)-grown layers show an equal distribution in the 4 possible directions. A spin coherence time of around 270 {mu}s was measured which is equivalent to that reported for material with similar isotopic purity. Although a higher degree of preferential orientation was achieved with (111)-grown layers (almost 100 %), the ease of growth and post-processing of the (113) orientation make it a potentially useful material for magnetometry or other quantum mechanical applications.
We report the first demonstration of the current-induced magnetization switching in a perpendicularly magnetized A1 CoPt single layer. We show that good perpendicular magnetic anisotropy can be obtained in a wide composition range of the A1 Co1-xPtx
single layers, which allows to fabricate perpendicularly magnetized CoPt single layer with composition gradient to break the inversion symmetry of the structure. By fabricating the gradient CoPt single layer, we have evaluated the SOT efficiency and successfully realized the SOT-induced magnetization switching. Our study provides an approach to realize the current-induced magnetization in the ferromagnetic single layers without attaching SOT source materials.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
