اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدInfluence of drying temperature on morphology of MAPbI$_3$ thin films and the performance of solar cells
81
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Photoelectric conversion efficiency of organic-inorganic perovskite solar cells has been rapidly raised and attracted great attention in recent years. The quality of perovskite films is vital for the performance of devices. We used the anti-solvent method to prepare CH$_3$NH$_3$PbI$_3$ thin films by spin coating and dried them at various temperature to transform adduct MAI.PbI$_2$.DMSO into CH$_3$NH$_3$PbI$_3$. We researched in detail on the relationship between surface morphology of MAPbI$_3$ thin films fabricated by the anti-solvent method and various drying temperature. We found that surface roughness and grain size of CH$_3$NH$_3$PbI$_3$ films together increased with increasing drying temperature. The larger grain size could efficiently reduce crystal boundaries which is advantageous for the suppression of photo-induced charge carrier recombination resulting in increase of FF. However, increase of surface roughness resulted in larger contact area at interface which might produce more tarp states and poorer wettability of HTM solution leading in decrease of Jsc. Surface morphology of MAPbI3 layer on the performance of solar cell devices is also an important research issue. By optimizing the drying temperature to 60 oC, the highest efficiency of 14.4% was achieved for the CH3NH3PbI3-based solar cell devices.
قيم البحث
اقرأ أيضاً
In terms of mixing graded TiO2 and SnO2 powders by solid-state reaction method, ITO was prepared. Using electron beam gun technology, ITO films with different thicknesses were prepared. The influence of film thickness on structure, electrical and opt
ical properties was studied. The XRD patterns were utilized to determine the structural parameters (lattice strain and crystallite size) of ITO with different thicknesses. It is observed that the average crystallite size increases as the film thickness increases, but the lattice strain decreases. SEM shows that as the film thickness increases, the grain size of ITO increases and improves. The electrical properties of ITO films with different thicknesses were measured by the standard four-point probe method. It can be seen that as the thickness of the ITO film increases from 75 nm to 325 nm, the resistivity decreases from 29x10^-4 Ohm/cm to 1.65x10^-4 Ohm/cm. This means that ITO films with lower electrical properties will be more suitable for high-efficiency CdTe solar cells. Three optical layer models (adhesive layer of the substrate/B-spline layer of ITO film/surface roughness layer) are used to calculate the film thickness with high-precision ellipsometry. In the higher T(lambda) and R(lambda) absorption regions, the absorption coefficient is determined to calculate the optical energy gap, which increases from 3.56 eV to 3.69 eV. Finally, the effects of ITO layers of various thicknesses on the performance of CdS/CdTe solar cells are also studied. When the thickness of the ITO window layer is 325 nm, Voc = 0.82 V, Jsc = 17 mA/cm2, and FF = 57.4%, the highest power conversion efficiency (PCE) is 8.6%.
Transition metal dichalcogenide (TMD) materials have emerged as promising candidates for thin film solar cells due to their wide bandgap range across the visible wavelengths, high absorption coefficient and ease of integration with both arbitrary sub
strates as well as conventional semiconductor technologies. However, reported TMD-based solar cells suffer from relatively low external quantum efficiencies (EQE) and low open circuit voltage due to unoptimized design and device fabrication. This paper studies $Pt/WSe_2$ vertical Schottky junction solar cells with various $WSe_2$ thicknesses in order to find the optimum absorber thickness.Also, we show that the photovoltaic performance can be improved via $Al_2O_3$ passivation which increases the EQE by up to 29.5% at 410 nm wavelength incident light. The overall resulting short circuit current improves through antireflection coating, surface doping, and surface trap passivation effects. Thanks to the ${Al_2O_3}$ coating, this work demonstrates a device with open circuit voltage ($V_{OC}$) of 380 mV and short circuit current density ($J_{SC}$) of 10.7 $mA/cm^2$. Finally, the impact of Schottky barrier height inhomogeneity at the $Pt/WSe_2$ contact is investigated as a source of open circuit voltage lowering in these devices
An optoelectronic optimization was carried out for an AlGaAs solar cell containing (i) an n-AlGaAs absorber layer with a graded bandgap and (ii) a periodically corrugated Ag backreflector combined with localized ohmic Pd-Ge-Au backcontacts. The bandg
ap of the absorber layer was varied either sinusoidally or linearly. An efficiency of 33.1% with the 2000-nm-thick n-AlGaAs absorber layer is predicted with linearly graded bandgap along with silver backreflector and localized ohmic backcontacts, in comparison to 27.4% efficiency obtained with homogeneous bandgap and a continuous ohmic backcontact. Sinusoidal grading of the bandgap {is predicted to enhance} the maximum efficiency to 34.5%. Thus, grading the bandgap of the absorber layer, along with a periodically corrugated Ag backreflector and localized ohmic Pd-Ge-Au backcontacts can help realize ultrathin and high-efficient AlGaAs solar cells for terrestrial applications.
The Shockley and Queisser limit, a well-known efficiency limit for a solar cell, is based on unrealistic physical assumptions and its maximum limit is seriously overestimated. To understand the power loss mechanisms of record-efficiency cells, a more
rigorous approach is necessary. Here, we have established a new formalism that can accurately predict absolute performance limits of solar cells in conventional thin film form. In particular, we have estimated the maximum efficiencies of 13 well-studied solar cell materials [GaAs, InP, CdTe, a-Si:H, CuInSe2, CuGaSe2, CuInGaSe2, Cu2ZnSnSe4, Cu2ZnSnS4, Cu2ZnSn(S,Se)4, Cu2ZnGeSe4, CH3NH3PbI3, HC(NH2)2PbI3] in a 1-um-thick physical limit. Our calculation shows that over 30% efficiencies can be achieved for absorber layers with sharp absorption edges (GaAs, InP, CdTe, CuInGaSe2, Cu2ZnGeSe4). Nevertheless, many record-efficiency polycrystalline solar cells, including hybrid perovskites, are limited by open-circuit voltage and fill-factor losses. We show that the maximum conversion efficiencies described here present new alternative limits that can predict the power generation of real-world solar cells.
We propose a two-stage multi-objective optimization framework for full scheme solar cell structure design and characterization, cost minimization and quantum efficiency maximization. We evaluated structures of 15 different cell designs simulated by v
arying material types and photodiode doping strategies. At first, non-dominated sorting genetic algorithm~II (NSGA-II) produced Pareto-optimal-solutions sets for respective cell designs. Then, on investigating quantum efficiencies of all cell designs produced by NSGA-II, we applied a new multi-objective optimization algorithm~II (OptIA-II) to discover the Pareto fronts of select (three) best cell designs. Our designed OptIA-II algorithm improved the quantum efficiencies of all select cell designs and reduced their fabrication costs. We observed that the cell design comprising an optimally doped zinc-oxide-based transparent conductive oxide (TCO) layer and rough silver back reflector (BR) offered a quantum efficiency ($Q_e$) of $0.6031.$ Overall, this paper provides a full characterization of cell structure designs. It derives a relationship between quantum efficiency, $Q_e$ of a cell with its TCO layers doping methods and TCO and BR layers material types. Our solar cells design characterization enables us to perform a cost-benefit analysis of solar cells usage in real-world applications
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
