اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدImpedances of Anisotropic Round and Rectangular Chambers
54
0
0.0
(
0
)
تأليف
Igor Zagorodnov
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We consider the calculation of electromagnetic fields generated by an electron bunch passing through an anisotropic transversally non-homogeneous vacuum chamber of round or rectangular cross-section with translational symmetry in the beam direction. The described algorithms are implemented in a numerical code and cross-checked on several examples.
قيم البحث
اقرأ أيضاً
We consider the calculation of electromagnetic fields generated by an electron bunch passing through a vacuum chamber structure that, in general, consists of an entry pipe, followed by some kind of transition or cavity, and ending in an exit pipe. We
limit our study to structures having rectangular cross-section, where the height can vary as function of longitudinal coordinate but the width and side walls remain fixed. For such structures, we derive a Fourier representation of the wake potentials through one-dimensional functions. A new numerical approach for calculating the wakes in such structures is proposed and implemented in the computer code ECHO(2D). The computation resource requirements for this approach are moderate and comparable to those for finding the wakes in 2D rotationally symmetric structures. Numerical examples obtained with the new numerical code are presented.
The Electron Multipacting (EM) phenomenon is a limiting factor for the achievement of high luminosity in accelerators for positively charged particles and for the performance of RF devices. At CERN, the Super Proton Synchrotron (SPS) must be upgraded
in order to feed the Large Hadron Collider (LHC) with 25 ns bunch spaced beams. At such small bunch spacing, EM may limit the performance of the SPS and consequently that of the LHC. To mitigate this phenomenon CERN is developing a carbon thin film coating with low Secondary Electron Yield (SEY) to coat the internal walls of the SPS dipoles beam pipes. This paper presents the progresses in the coating technology, the performance of the carbon coatings and the strategy for a large scale production.
Studies were made into the arise and an evolution of the beam breakup (BBU) instability in a rectangular dielectric resonator under excitation by a sequence of relativistic electron bunches. The dielectric resonator is a metal rectangular waveguide $
R_{26}$ $(45mmtimes 90mm)$ with Teflon dielectric slabs $8.2mm$ thick (dielectric constant $varepsilon=2.051$) located along the wide side of the resonator. The wavelength of the $LM_{21}$ operating mode having a symmetric profile of the longitudinal electric field component is $53.2mm$. The electron energy of bunches is $4.5MeV$ , the charge of each bunch is $6.4nC$, the bunch repetition period is equal to twice the wavelength of the $LM_{21}$ mode. By the use of numerical PIC simulations, the charge losses of electron bunches on the dielectric plates were investigated as the bunches were displaced relative to the cavity axis. It is found that the charge losses on the dielectric slabs due to the BBU instability do not exceed $5%$. When the bunch repetition period is changed to a multiple of another eigenfrequency (e.g., the $LM_{11}$ mode), the charge losses of drive bunches do not change appreciably.
Some modifications of a Rectangular Waveguide HOM couplers for TESLA superstructure have been investigated. These RWG HOM couplers are to be installed between the cavities of the superstructure and also at the both ends of it. We investigated a RWG H
OM coupler attached to the beam pipe through the slots orientated along beam pipe axis (longitudinal slots), perpendicular to it (azimutal slots) and at some angle to this axis. For dipole modes of both polarizations damping two RWG in every design were used. This paper presents the results obtained for scaled-up setup at 3 GHz at room temperature. The advantages of HOM coupler with longitudinal slots for damping dipole modes and compact HOM coupler with slots at some angle to the axis are shown. Arrangement of HOM coupler in cryostat and heating due to HOM and FM losses are presented. Calculations and design of the feeding RWG coupler for superstructure are also presented.
Simulating inhomogeneous flows with different characteristic scales in different coordinate directions using the collide-and-stream based lattice Boltzmann methods (LBM) can be accomplished efficiently using rectangular lattice grids. We develop and
investigate a new rectangular central moment LBM based on non-orthogonal moment basis (referred to as RC-LBM). The equilibria to which the central moments relax under collision in this approach are obtained from matching with those corresponding to the continuous Maxwell distribution. A Chapman-Enskog analysis is performed to derive the correction terms to the second order moment equilibria involving the grid aspect ratio and velocity gradients that restores the isotropy of the viscous stress tensor and eliminates the non-Galilean invariant cubic velocity terms of the resulting hydrodynamical equations. A special case of this rectangular formulation involving the raw moments (referred to as the RNR-LBM) is also constructed. The resulting schemes represent a considerable simplification, especially for the transformation matrices and isotropy corrections, and improvement over the existing MRT-LB schemes on rectangular lattice grids that use orthogonal moment basis. Numerical validation study of both the RC-LBM and RNR-LBM for a variety of benchmark flow problems are performed that show good accuracy at various grid aspect ratios. The ability of our proposed schemes to simulate flows using relatively lower grid aspect ratios than considered in prior rectangular LB approaches is demonstrated. Furthermore, simulations reveal the superior stability characteristics of the RC-LBM over RNR-LBM in handling shear flows at lower viscosities and/or higher characteristic velocities. In addition, computational advantages of using our rectangular LB formulation in lieu of that based on the square lattice is shown.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
