اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدStrain effects on oxygen vacancy formation energy in perovskites
146
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Oxygen vacancy formation energy is an important quantity for enabling fast oxygen diffusion and oxygen catalysis in technologies like solid oxide fuel cells. Both previous literature in various systems and our calculations in LaMnO3, La0.75Sr0.25MnO3, LaFeO3, and La0.75Sr0.25FeO3, show mixed results for the direction and magnitude of the change in vacancy formation energy with strain. This paper develops a model to make sense of the different trend shapes in vacancy formation energy versus strain. We model strain effects using a set of consistent ab initio calculations, and demonstrate that our calculated results may be simply explained in terms of vacancy formation volume and changes in elastic constants between the bulk and defected states. A positive vacancy formation volume contributes to decreased vacancy formation energy under tensile strain, and an increase in elastic constants contributes to increases in vacancy formation energy with compressive and tensile strains, and vice versa. The vacancy formation volume dominates the linear portion of the vacancy formation energy strain response, while its curvature is governed by the vacancy-induced change in elastic constants. We show results sensitive to B-site cation, A-site doping, tilt system, and vacancy placement, which contributions may be averaged under thermally averaged conditions. In general, vacancy formation energies for most systems calculated here decreased with tensile strain, with about a 30-100 meV/% strain decrease with biaxial strain for those systems which showed a decrease in vacancy formation energy. Experimental verification is necessary to confirm the model outside of calculation.
قيم البحث
اقرأ أيضاً
Fast oxygen transport materials are necessary for a range of technologies, including efficient and cost-effective solid oxide fuel cells, gas separation membranes, oxygen sensors, chemical looping devices, and memristors. Strain is often proposed as
a method to enhance the performance of oxygen transport materials, but the magnitude of its effect and its underlying mechanisms are not well-understood, particularly in the widely-used perovskite-structured oxygen conductors. This work reports on an ab initio prediction of strain effects on migration energetics for nine perovskite systems of the form LaBO3, where B = [Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Ga]. Biaxial strain, as might be easily produced in epitaxial systems, is predicted to lead to approximately linear changes in migration energy. We find that tensile biaxial strain reduces the oxygen vacancy migration barrier across the systems studied by an average of 66 meV per percent strain for a single selected hop, with a low of 36 and a high of 89 meV decrease in migration barrier per percent strain across all systems. The estimated range for the change in migration barrier within each system is approximately 25 meV per percent strain when considering all hops. These results suggest that strain can significantly impact transport in these materials, e.g., a 2% tensile strain can increase the diffusion coefficient by about three orders of magnitude at 300 K (one order of magnitude at 500 {deg}C or 773 K) for one of the most strain-responsive materials calculated here (LaCrO3). We show that a simple elasticity model, which assumes only dilative or compressive strain in a cubic environment and a fixed migration volume, can qualitatively but not quantitatively model the strain dependence of the migration energy, suggesting that factors not captured by continuum elasticity play a significant role in the strain response.
We use first-principles calculations to investigate the stability of bi-axially strained textit{Pnma} perovskite CaMnO$_3$ towards the formation of oxygen vacancies. Our motivation is provided by promising indications that novel material properties c
an be engineered by application of strain through coherent heteroepitaxy in thin films. While it is usually assumed that such epitaxial strain is accommodated primarily by changes in intrinsic lattice constants, point defect formation is also a likely strain relaxation mechanism. This is particularly true at the large strain magnitudes ($>$4%) which first-principles calculations often suggest are required to induce new functionalities. We find a strong dependence of oxygen vacancy defect formation energy on strain, with tensile strain lowering the formation energy consistent with the increasing molar volume with increasing oxygen deficiency. In addition, we find that strain differentiates the formation energy for different lattice sites, suggesting its use as a route to engineering vacancy ordering in epitaxial thin films.
Irradiation-induced vacancy evolution in face-centered cubic (FCC) Ni under mechanical strains was studied using molecular dynamics simulations. Applied hydrostatic strain led to different stable forms of vacancy clusters, i.e., voids under strain >=
+2% and stacking fault tetrahedras (SFTs) under strain <= 0. Direct transitions between SFT and void revealed that increasing strain magnitude facilitated the thermodynamic stability and dynamical evolution. The estimated free energy difference could well validate the dynamical simulations results by accounting for entropic contribution, which was revealed to play an important role in the thermodynamic stability of vacancy clusters in FCC Ni.
There is considerable interest in the pH-dependent switchable biocatalytic properties of cerium oxide nanoparticles (CeNPs) in biomedicine, where these materials exhibit beneficial antioxidant activity against reactive oxygen species at neutral and b
asic physiological pH but cytotoxic prooxidant activity at acidic pathological pH. Oxygen vacancies play a key role in such biocatalytic activities. While the general characteristics of the role of oxygen vacancies are known, the mechanism of their action at the atomic scale under different pH conditions has yet to be elucidated. The present work applies density functional theory (DFT) calculations to interpret the pH-induced behavior of the stable {111} surface of CeO2 at the atomic scale. Analysis of the surface-adsorbed media species reveals the critical role of pH on the reversibility of the Ce3+ and Ce4+ redox equilibria and the formation and annihilation of the oxygen vacancies. Under acidic conditions, this reversible switching is hindered owing to incomplete volumetric filling of the oxygen vacancies by the oxygen in the water molecules, hence effective retention of the oxygen vacancies, and consequent inhibition of redox biomimetic reactions. Under neutral and basic conditions, the capacity for this reversible switching is preserved due to complete filling of the oxygen vacancies by the OH ions owing to their ready size accommodation, thereby retaining the capacity for performing redox biomimetic reactions cyclically.
Applying external strain is an efficient way to manipulate the site preference of dopants in semiconductors, however, the validity of the previous continuum elastic model for the strain influence on the doping forma- tion energy is still under debate
. In this paper, by combining quantum mechanical theoretical analysis and first-principles calculations, we show that if the occupation change of different orbitals caused by the strain is negligible, the continuum elastic model is valid, otherwise it will fail. Our theory is confirmed by first-principles calculation of Mn-doped GaAs system. Moreover, we show that under compressive strain the hole density, thus the Curie temperature TC can increase in Mn-doped spintronic materials.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
