اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدImpact of contact resistance in Lorenz number measurements
122
0
0.0
(
0
)
تأليف
Kin Chung Fong
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We analyze the effect of contact resistance on the Lorenz number measurement based on direct electronic thermal conductivity experiments. The contact resistance can significantly limit the experimental measured value when the Lorenz number is enhanced, but not as much so when it is suppressed, should the Wiedemann-Franz law be violated. The result provides the conditions of the potential false negative error and highlights the importance of improving the contact resistance in studying non-Fermi liquid behavior in thermal transport experiments.
قيم البحث
اقرأ أيضاً
We report a systematic study of the contact resistance present at the interface between a metal (Ti) and graphene layers of different, known thickness. By comparing devices fabricated on 11 graphene flakes we demonstrate that the contact resistance i
s quantitatively the same for single-, bi-, and tri-layer graphene ($sim800 pm 200 Omega mu m$), and is in all cases independent of gate voltage and temperature. We argue that the observed behavior is due to charge transfer from the metal, causing the Fermi level in the graphene region under the contacts to shift far away from the charge neutrality point.
We show experimentally that in nanometer scaled superconductor/normal metal hybrid devices and in a small window of contact resistances, crossed Andreev reflection (CAR) can dominate the nonlocal transport for all energies below the superconducting g
ap. Besides CAR, elastic cotunneling (EC) and nonlocal charge imbalance (CI) can be identified as competing subgap transport mechanisms in temperature dependent four-terminal nonlocal measurements. We demonstrate a systematic change of the nonlocal resistance vs. bias characteristics with increasing contact resistances, which can be varied in the fabrication process. For samples with higher contact resistances, CAR is weakened relative to EC in the midgap regime, possibly due to dynamical Coulomb blockade. Gaining control of CAR is an important step towards the realization of a solid state entangler.
Metal contacts have been identified to be a key technological bottleneck for the realization of viable graphene electronics. Recently, it was observed that for structures that possess both a top and a bottom gate, the electron-hole conductance asymme
try can be modulated by the bottom gate. In this letter, we explain this observation by postulating the presence of an effective thin interfacial dielectric layer between the metal contact and the underlying graphene. Electrical results from quantum transport calculations accounting for this modified electrostatics corroborate well with the experimentally measured contact resistances. Our study indicates that the engineering of metal- graphene interface is a crucial step towards reducing the contact resistance for high performance graphene transistors.
The extremely high carrier mobility and the unique band structure, make graphene very useful for field-effect transistor applications. According to several works, the primary limitation to graphene based transistor performance is not related to the m
aterial quality, but to extrinsic factors that affect the electronic transport properties. One of the most important parasitic element is the contact resistance appearing between graphene and the metal electrodes functioning as the source and the drain. Ohmic contacts to graphene, with low contact resistances, are necessary for injection and extraction of majority charge carriers to prevent transistor parameter fluctuations caused by variations of the contact resistance. The International Technology Roadmap for Semiconductors, toward integration and down-scaling of graphene electronic devices, identifies as a challenge the development of a CMOS compatible process that enables reproducible formation of low contact resistance. However, the contact resistance is still not well understood despite it is a crucial barrier towards further improvements. In this paper, we review the experimental and theoretical activity that in the last decade has been focusing on the reduction of the contact resistance in graphene transistors. We will summarize the specific properties of graphene-metal contacts with particular attention to the nature of metals, impact of fabrication process, Fermi level pinning, interface modifications induced through surface processes, charge transport mechanism, and edge contact formation.
Capillary and van der Waals forces cause nanotubes to deform or even collapse under metal contacts. Using ab-initio bandstructure calculations, we find that these deformations reduce the bandgap by as much as 30%, while fully collapsed nanotubes beco
me metallic. Moreover degeneracy lifting, due to the broken axial symmetry and wavefunctions mismatch between the fully collapsed and the round portions of a CNT, leads to a three times higher contact resistance. The latter we demonstrate by contact resistance calculations within the tight-binding approach.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
