اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدContact resistance in graphene-based devices
147
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We report a systematic study of the contact resistance present at the interface between a metal (Ti) and graphene layers of different, known thickness. By comparing devices fabricated on 11 graphene flakes we demonstrate that the contact resistance is quantitatively the same for single-, bi-, and tri-layer graphene ($sim800 pm 200 Omega mu m$), and is in all cases independent of gate voltage and temperature. We argue that the observed behavior is due to charge transfer from the metal, causing the Fermi level in the graphene region under the contacts to shift far away from the charge neutrality point.
قيم البحث
اقرأ أيضاً
The extremely high carrier mobility and the unique band structure, make graphene very useful for field-effect transistor applications. According to several works, the primary limitation to graphene based transistor performance is not related to the m
aterial quality, but to extrinsic factors that affect the electronic transport properties. One of the most important parasitic element is the contact resistance appearing between graphene and the metal electrodes functioning as the source and the drain. Ohmic contacts to graphene, with low contact resistances, are necessary for injection and extraction of majority charge carriers to prevent transistor parameter fluctuations caused by variations of the contact resistance. The International Technology Roadmap for Semiconductors, toward integration and down-scaling of graphene electronic devices, identifies as a challenge the development of a CMOS compatible process that enables reproducible formation of low contact resistance. However, the contact resistance is still not well understood despite it is a crucial barrier towards further improvements. In this paper, we review the experimental and theoretical activity that in the last decade has been focusing on the reduction of the contact resistance in graphene transistors. We will summarize the specific properties of graphene-metal contacts with particular attention to the nature of metals, impact of fabrication process, Fermi level pinning, interface modifications induced through surface processes, charge transport mechanism, and edge contact formation.
The metal-graphene contact resistance is a technological bottleneck for the realization of viable graphene based electronics. We report a useful model to find the gate tunable components of this resistance determined by the sequential tunneling of ca
rriers between the 3D-metal and 2D-graphene underneath followed by Klein tunneling to the graphene in the channel. This model quantifies the intrinsic factors that control that resistance, including the effect of unintended chemical doping. Our results agree with experimental results for several metals.
We discuss transport through double gated single and few layer graphene devices. This kind of device configuration has been used to investigate the modulation of the energy band structure through the application of an external perpendicular electric
field, a unique property of few layer graphene systems. Here we discuss technological details that are important for the fabrication of top gated structures, based on electron-gun evaporation of SiO$_2$. We perform a statistical study that demonstrates how --contrary to expectations-- the breakdown field of electron-gun evaporated thin SiO$_2$ films is comparable to that of thermally grown oxide layers. We find that a high breakdown field can be achieved in evaporated SiO$_2$ only if the oxide deposition is directly followed by the metallization of the top electrodes, without exposure to air of the SiO$_2$ layer.
We study the contact resistance and the transfer characteristics of back-gated field effect transistors of mono- and bi-layer graphene. We measure specific contact resistivity of ~7kohm*um2 and ~30kohm*um2 for Ni and Ti, respectively. We show that th
e contact resistance is a significant contributor to the total source-to-drain resistance and it is modulated by the back-gate voltage. We measure transfer characteristics showing double dip feature that we explain as the effect of doping due to charge transfer from the contacts causing minimum density of states for graphene under the contacts and in the channel at different gate voltage.
We have performed a metrological characterization of the quantum Hall resistance in a 1 $mu$m wide graphene Hall-bar. The longitudinal resistivity in the center of the $ u=pm 2$ quantum Hall plateaus vanishes within the measurement noise of 20 m$Omeg
a$ upto 2 $mu$A. Our results show that the quantization of these plateaus is within the experimental uncertainty (15 ppm for 1.5$ mu$A current) equal to that in conventional semiconductors. The principal limitation of the present experiments are the relatively high contact resistances in the quantum Hall regime, leading to a significantly increased noise across the voltage contacts and a heating of the sample when a high current is applied.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
