اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدInfluence of twist boundary on deformation behaviour of <100> BCC Fe nanowires
124
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Molecular dynamics simulations revealed significant difference in deformation behaviour of $<$100$>$ BCC Fe nanowires with and without twist boundary. The plastic deformation in perfect $<$100$>$ BCC Fe nanowire was dominated by twinning and reorientation to $<$110$>$ followed by further deformation by slip mode. On the contrary, $<$100$>$ BCC Fe nanowire with a twist boundary deformed by slip at low plastic strains followed by twinning at high strains and absence of full reorientation. The results suggest that the deformation in $<$100$>$ BCC Fe nanowire by dislocation slip is preferred over twinning in the presence of initial dislocations or dislocation networks. The results also explain the absence of extensive twinning in bulk materials, which inherently contains large number of dislocations.
قيم البحث
اقرأ أيضاً
Molecular dynamics simulations have been performed to understand the influence of temperature on the tensile deformation and fracture behavior of $<$111$>$ BCC Fe nanowires. The simulations have been carried out at different temperatures in the range
10-1000 K employing a constant strain rate of $1times$ $10^8$ $s^{-1}$. The results indicate that at low temperatures (10-375 K), the nanowires yield through the nucleation of a sharp crack and fails in brittle manner. On the other hand, nucleation of multiple 1/2$<$111$>$ dislocations at yielding followed by significant plastic deformation leading to ductile failure has been observed at high temperatures in the range 450-1000 K. At the intermediate temperature of 400 K, the nanowire yields through nucleation of crack associated with many mobile 1/2$<$111$>$ and immobile $<$100$>$ dislocations at the crack tip and fails in ductile manner. The ductile-brittle transition observed in $<$111$>$ BCC Fe nanowires is appropriately reflected in the stress-strain behavior and plastic strain at failure. The ductile-brittle transition increases with increasing nanowire size. The change in fracture behavior has been discussed in terms of the relative variations in yield and fracture stresses and change in slip behavior with respect to temperature. Further, the dislocation multiplication mechanism assisted by the kink nucleation from the nanowire surface observed at high temperatures has been presented.
Molecular dynamics simulations have been performed to understand the variations in deformation mechanisms of Cu nanowires as a function of orientation and loading mode (tension or compression). Cu nanowires of different crystallographic orientations
distributed uniformly on the standard stereographic triangle have been considered under tensile and compressive loading. The simulation results indicate that under compressive loading, the orientations close to $<$100$>$ corner deform by twinning mechanism, while the remaining orientations deform by dislocation slip. On the other hand, all the nanowires deform by twinning mechanism under tensile loading. Further, the orientations close to $<$110$>$ and $<$111$>$ corner exhibit tension-compression asymmetry in deformation mechanisms. In addition to deformation mechanisms, Cu nanowires also display tension-compression asymmetry in yield stress. The orientations close to $<$001$>$ corner exhibits higher yield stress in tension than in compression, while the opposite behaviour (higher yield stress in compression than in tension) has been observed in orientations close to $<$110$>$ and $<$111$>$ corners. For the specific orientation of $<$102$>$, the yield stress asymmetry has not been observed. The tension-compression asymmetry in deformation mechanisms has been explained based on the parameter $alpha_M$, defined as the ratio of Schmid factors for leading and trailing partial dislocations. Similarly, the asymmetry in yield stress values has been attributed to the different Schmid factor values for leading partial dislocations under tensile and compressive loading.
Crack growth behaviour along the coherent twin boundary (CTB), i.e., $Sigma$3{112} of BCC Fe is investigated using molecular dynamics (MD) simulations. The growth of an atomistically sharp crack with {112}$<$110$>$ orientation has been examined along
the two opposite $<$111$>$ directions of CTB under mode-I loading at a constant strain rate. Separate MD simulations were carried out with crack inserted in the left side, right side and middle of the specimen model system. The results indicate that the crack grows differently along the two opposite $<$111$>$ directions. In case of a crack inserted in the left side, the crack grows in ductile manner, while it propagates in semi-brittle manner in the case of crack inserted in the right side. The directional dependence of crack growth along the CTB is also confirmed by the stress-strain behaviour. This anisotropy in crack growth behaviour has been attributed to the twinning-antitwinning asymmetry of 1/6$<$111$>$ partial dislocations on {112} planes.
Nanoparticles usually exhibit pronounced anisotropic properties, and a close insight into the atomic-scale deformation mechanisms is of great interest. In present study, atomic simulations are conducted to analyze the compression of bcc nanoparticles
, and orientation-dependent features are addressed. It is revealed that surface morphology under indenter predominantly governs the initial elastic response. The loading curve follows the flat punch contact model in [110] compression, while it obeys the Hertzian contact model in [111] and [001] compressions. In plastic deformation regime, full dislocation gliding is dominated in [110] compression, while deformation twinning is prominent in [111] compression, and these two mechanisms coexist in [001] compression. Such deformation mechanisms are distinct from those in bulk crystals under nanoindentation and nanopillars under compression, and the major differences are also illuminated. Our results provide an atomic perspective on the mechanical behaviors of bcc nanoparticles and are helpful for the design of nanoparticle-based components and systems.
For the first time, we report the formation of pentagonal atomic chains during tensile deformation of ultra thin BCC Fe nanowires. Extensive molecular dynamics simulations have been performed on $<$100$>$/{110} BCC Fe nanowires with different cross s
ection width varying from 0.404 to 3.634 nm at temperatures ranging from 10 to 900 K. The results indicate that above certain temperature, long and stable pentagonal atomic chains form in BCC Fe nanowires with cross section width less than 2.83 nm. The temperature, above which the pentagonal chains form, increases with increase in nanowire size. The pentagonal chains have been observed to be highly stable over large plastic strains and contribute to high ductility in Fe nanowires.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
