اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدSelective AP-sequence Based Indoor Localization without Site Survey
113
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this paper, we propose an indoor localization system employing ordered sequence of access points (APs) based on received signal strength (RSS). Unlike existing indoor localization systems, our approach does not require any time-consuming and laborious site survey phase to characterize the radio signals in the environment. To be precise, we construct the fingerprint map by cutting the layouts of the interested area into regions with only the knowledge of positions of APs. This can be done offline within a second and has a potential for practical use. The localization is then achieved by matching the ordered AP-sequence to the ones in the fingerprint map. Different from traditional fingerprinting that employing all APs information, we use only selected APs to perform localization, due to the fact that, without site survey, the possibility in obtaining the correct AP sequence is lower if it involves more APs. Experimental results show that, the proposed system achieves localization accuracy < 5m with an accumulative density function (CDF) of 50% to 60% depending on the density of APs. Furthermore, we observe that, using all APs for localization might not achieve the best localization accuracy, e.g. in our case, 4 APs out of total 7 APs achieves the best performance. In practice, the number of APs used to perform localization should be a design parameter based on the placement of APs.
قيم البحث
اقرأ أيضاً
We study the problem of indoor localization using commodity WiFi channel state information (CSI) measurements. The accuracy of methods developed to address this problem is limited by the overall bandwidth used by the WiFi device as well as various ty
pes of signal distortions imposed by the underlying hardware. In this paper, we propose a localization method that performs channel impulse response (CIR) estimation by splicing measured CSI over multiple WiFi bands. In order to overcome hardware-induced phase distortions, we propose a phase retrieval (PR) scheme that only uses CSI magnitude values to estimate the CIR. To achieve high localization accuracy, the PR scheme involves a sparse recovery step, which exploits the fact that the CIR is sparse over the delay domain, due to the small number of contributing signal paths in an indoor environment. Simulation results indicate that our approach outperforms the state of the art by an order of magnitude (cm-level localization accuracy) for more than 90% of the trials and for various SNR regimes.
The proliferation of wireless localization technologies provides a promising future for serving human beings in indoor scenarios. Their applications include real-time tracking, activity recognition, health care, navigation, emergence detection, and t
arget-of-interest monitoring, among others. Additionally, indoor localization technologies address the inefficiency of GPS (Global Positioning System) inside buildings. Since people spend most of their time in indoor environments, indoor tracking service is in great public demand. Based on this observation, this paper aims to provide a better understanding of state-of-the-art technologies and stimulate new research efforts in this field. For these purposes, existing localization technologies that can be used for tracking individuals in indoor environments are reviewed, along with some further discussions.
Indoor positioning systems using visible light communication (VLC) have potential applications in smart buildings, for instance, in developing economical, easy-to-use, widely accessible positioning system based on light-emitting diodes. Thus using VL
Cs, we introduce a new fuzzy-based system for indoor localization in this paper. The system processes data from transmitters (i.e., anchor nodes) and delivers the calculated position of a receiver. A particle swarm optimization (PSO) technique is then employed to obtain the optimal configuration of the proposed fuzzy logic controllers (FLCs). Specifically, the proposed PSO technique optimizes the membership functions of the FLCs by adjusting their range to achieve the best results regarding the localization reliability. We demonstrate the utility of the proposed approach using experiments.
We introduce WiCluster, a new machine learning (ML) approach for passive indoor positioning using radio frequency (RF) channel state information (CSI). WiCluster can predict both a zone-level position and a precise 2D or 3D position, without using an
y precise position labels during training. Prior CSI-based indoor positioning work has relied on non-parametric approaches using digital signal-processing (DSP) and, more recently, parametric approaches (e.g., fully supervised ML methods). However these do not handle the complexity of real-world environments well and do not meet requirements for large-scale commercial deployments: the accuracy of DSP-based method deteriorates significantly in non-line-of-sight conditions, while supervised ML methods need large amounts of hard-to-acquire centimeter accuracy position labels. In contrast, WiCluster is both precise and requires weaker label-information that can be easily collected. Our first contribution is a novel dimensionality reduction method for charting. It combines a triplet-loss with a multi-scale clustering-loss to map the high-dimensional CSI representation to a 2D/3D latent space. Our second contribution is two weakly supervised losses that map this latent space into a Cartesian map, resulting in meter-accuracy position results. These losses only require simple to acquire priors: a sketch of the floorplan, approximate location of access-point locations and a few CSI packets that are labeled with the corresponding zone in the floorplan. Thirdly, we report results and a robustness study for 2D positioning in a single-floor office building and 3D positioning in a two-floor home to show the robustness of our method.
Modeling human mobility has a wide range of applications from urban planning to simulations of disease spread. It is well known that humans spend 80% of their time indoors but modeling indoor human mobility is challenging due to three main reasons: (
i) the absence of easily acquirable, reliable, low-cost indoor mobility datasets, (ii) high prediction space in modeling the frequent indoor mobility, and (iii) multi-scalar periodicity and correlations in mobility. To deal with all these challenges, we propose WiFiMod, a Transformer-based, data-driven approach that models indoor human mobility at multiple spatial scales using WiFi system logs. WiFiMod takes as input enterprise WiFi system logs to extract human mobility trajectories from smartphone digital traces. Next, for each extracted trajectory, we identify the mobility features at multiple spatial scales, macro, and micro, to design a multi-modal embedding Transformer that predicts user mobility for several hours to an entire day across multiple spatial granularities. Multi-modal embedding captures the mobility periodicity and correlations across various scales while Transformers capture long-term mobility dependencies boosting model prediction performance. This approach significantly reduces the prediction space by first predicting macro mobility, then modeling indoor scale mobility, micro-mobility, conditioned on the estimated macro mobility distribution, thereby using the topological constraint of the macro-scale. Experimental results show that WiFiMod achieves a prediction accuracy of at least 10% points higher than the current state-of-art models. Additionally, we present 3 real-world applications of WiFiMod - (i) predict high-density hot pockets for policy-making decisions for COVID19 or ILI, (ii) generate a realistic simulation of indoor mobility, (iii) design personal assistants.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
