اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدYield, Area and Energy Optimization in Stt-MRAMs using failure aware ECC
72
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Spin Transfer Torque MRAMs are attractive due to their non-volatility, high density and zero leakage. However, STT-MRAMs suffer from poor reliability due to shared read and write paths. Additionally, conflicting requirements for data retention and write-ability (both related to the energy barrier height of the magnet) makes design more challenging. Furthermore, the energy barrier height depends on the physical dimensions of the free layer. Any variations in the dimensions of the free layer lead to variations in the energy barrier height. In order to address poor reliability of STT-MRAMs, usage of Error Correcting Codes (ECC) have been proposed. Unlike traditional CMOS memory technologies, ECC is expected to correct both soft and hard errors in STT_MRAMs. To achieve acceptable yield with low write power, stronger ECC is required, resulting in increased number of encoded bits and degraded memory efficiency. In this paper, we propose Failure aware ECC (FaECC), which masks permanent faults while maintaining the same correction capability for soft errors without increased encoded bits. Furthermore, we investigate the impact of process variations on run-time reliability of STT-MRAMs. We provide an analysis on the impact of process variations on the life-time of the free layer and retention failures. In order to analyze the effectiveness of our methodology, we developed a cross-layer simulation framework that consists of device, circuit and array level analysis of STT-MRAM memory arrays. Our results show that using FaECC relaxes the requirements on the energy barrier height, which reduces the write energy and results in smaller access transistor size and memory array area. Keywords: STT-MRAM, reliability, Error Correcting Codes, ECC, magnetic memory
قيم البحث
اقرأ أيضاً
As one of the most promising emerging non-volatile memory (NVM) technologies, spin-transfer torque magnetic random access memory (STT-MRAM) has attracted significant research attention due to several features such as high density, zero standby leakag
e, and nearly unlimited endurance. However, a high-quality test solution is required prior to the commercialization of STT-MRAM. In this paper, we present all STT-MRAM failure mechanisms: manufacturing defects, extreme process variations, magnetic coupling, STT-switching stochasticity, and thermal fluctuation. The resultant fault models including permanent faults and transient faults are classified and discussed. Moreover, the limited test algorithms and design-for-testability (DfT) designs proposed in the literature are also covered. It is clear that test solutions for STT-MRAMs are far from well established yet, especially when considering a defective part per billion (DPPB) level requirement. We present the main challenges on the STT-MRAM testing topic at three levels: failure mechanisms, fault modeling, and test/DfT designs.
Dynamic voltage scaling (DVS) is one of the most effective techniques for reducing energy consumption in embedded and real-time systems. However, traditional DVS algorithms have inherent limitations on their capability in energy saving since they rar
ely take into account the actual application requirements and often exploit fixed timing constraints of real-time tasks. Taking advantage of application adaptation, an enhanced energy-aware feedback scheduling (EEAFS) scheme is proposed, which integrates feedback scheduling with DVS. To achieve further reduction in energy consumption over pure DVS while not jeopardizing the quality of control, the sampling period of each control loop is adapted to its actual control performance, thus exploring flexible timing constraints on control tasks. Extensive simulation results are given to demonstrate the effectiveness of EEAFS under different scenarios. Compared with the optimal pure DVS scheme, EEAFS saves much more energy while yielding comparable control performance.
Factors driving success and failure in CS1 are the subject of much study but less so for CS2. This paper investigates the transition from CS1 to CS2 in search of leading indicators of success in CS2. Both CS1 and CS2 at the University of North Caroli
na Wilmington (UNCW) are taught in Python with annual enrollments of 300 and 150 respectively. In this paper, we report on the following research questions: 1) Are CS1 grades indicators of CS2 grades? 2) Does a quantitative relationship exist between CS2 course grade and a modified version of the SCS1 concept inventory? 3) What are the most challenging aspects of CS2, and how well does CS1 prepare students for CS2 from the students perspective? We provide a quantitative analysis of 2300 CS1 and CS2 course grades from 2013--2019. In Spring 2019, we administered a modified version of the SCS1 concept inventory to 44 students in the first week of CS2. Further, 69 students completed an exit questionnaire at the conclusion of CS2 to gain qualitative student feedback on their challenges in CS2 and on how well CS1 prepared them for CS2. We find that 56% of students grades were lower in CS2 than CS1, 18% improved their grades, and 26% earned the same grade. Of the changes, 62% were within one grade point. We find a statistically significant correlation between the modified SCS1 score and CS2 grade points. Students identify linked lists and class/object concepts among the most challenging. Student feedback on CS2 challenges and the adequacy of their CS1 preparations identify possible avenues for improving the CS1-CS2 transition.
A PEM micro fuel cell system is described which is based on self-breathing PEM micro fuel cells in the power range between 1 mW and 1W. Hydrogen is supplied with on-demand hydrogen production with help of a galvanic cell, that produces hydrogen when
Zn reacts with water. The system can be used as a battery replacement for low power applications and has the potential to improve the run time of autonomous systems. The efficiency has been investigated as function of fuel cell construction and tested for several load profiles.
Today, hot embossing and injection molding belong to the established plastic molding processes in microengineering. Based on experimental findings, a variety of microstructures have been replicated so far using the processes. However, with increasing
requirements regarding the embossing surface and the simultaneous decrease of the structure size down into the nanorange, increasing know-how is needed to adapt hot embossing to industrial standards. To reach this objective, a German-Canadian cooperation project has been launched to study hot embossing theoretically by a process simulation and experimentally. The present publication shall report about the first results of the simulation - the modeling and simulation of large area replication based on an eight inch microstructured mold.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
