اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCrack patterns over uneven substrates
107
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Cracks in thin layers are influenced by what lies beneath them. From buried craters to crocodile skin, crack patterns are found over an enormous range of length scales. Regardless of absolute size, their substrates can dramatically influence how cracks form, guiding them in some cases, or shielding regions from them in others. Here we investigate how a substrates shape affects the appearance of cracks above it, by preparing mud cracks over sinusoidally varying surfaces. We find that as the thickness of the cracking layer increases, the observed crack patterns change from wavy to ladder-like to isotropic. Two order parameters are introduced to measure the relative alignment of these crack networks, and, along with Fourier methods, are used to characterise the transitions between crack pattern types. Finally, we explain these results with a model, based on the Griffith criteria of fracture, that identifies the conditions for which straight or wavy cracks will be seen, and predicts how well-ordered the cracks will be. Our metrics and results can be applied to any situation where connected networks of cracks are expected, or found.
قيم البحث
اقرأ أيضاً
-- A scientific hurdle in manufacturing solid films by drying colloidal layers is preventing them from fracturing. This paper examines how the drying rate of colloidal liquids influences the particle packing at the nanoscale in correlation with the c
rack patterns observed at the macroscale. Increasing the drying rate results in more ordered, denser solid structures, and the dried samples have more cracks.Yet, introducing a holding period (at a prescribed point) during the drying protocol results in a more disordered solid structure with significantly less cracks. To interpret these observations, this paper conjectures that a longer drying protocol favors the formation of aggregates. It is further argued that the number and size of the aggregates increase as the drying rate decreases. This results in the formation of a more disordered, porous film from the viewpoint of the particle packing, and a more resistant film, i.e. less cracks, from the macroscale viewpoint.
The propagation of surface water waves interacting with a current and an uneven bottom is studied. Such a situation is typical for ocean waves where the winds generate currents in the top layer of the ocean. The role of the bottom topography is taken
into account since it also influences the local wave and current patterns. Specific scaling of the variables is selected which leads to approximations of Boussinesq and KdV types. The arising KdV equation with variable coefficients, dependent on the bottom topography, is studied numerically when the initial condition is in the form of the one soliton solution for the initial depth. Emergence of new solitons is observed as a result of the wave interaction with the uneven bottom.
Within mean-field theory we study wetting of elastic substrates. Our analysis is based on a grand canonical free energy functional of the fluid number density and of the substrate displacement field. The substrate is described in terms of the linear
theory of elasticity, parametrized by two Lame coefficients. The fluid contribution is of the van der Waals type. Two potentials characterize the interparticle interactions in the system. The long-ranged attraction between the fluid particles is described by a potential $w(r)$, and $v(r)$ characterizes the substrate-fluid interaction. By integrating out the elastic degrees of freedom we obtain an effective theory for the fluid number density alone. Its structure is similar to the one for wetting of an inert substrate. However, the potential $w(r)$ is replaced by an effective potential which, in addition to $w(r)$, contains a term bilinear in $v(r)$. We discuss the corresponding wetting transitions in terms of an effective interface potential $omega(ell)$, where $ell$ denotes the thickness of the wetting layer. We show that in the case of algebraically decaying interactions the elasticity of the substrate may suppress critical wetting transitions, and may even turn them first order.
Many clays, soils, biological tissues, foods, and coatings are shrinkable, granular materials: they are composed of packed, hydrated grains that shrink when dried. In many cases, these packings crack during drying, critically hindering applications.
However, while cracking has been widely studied for bulk gels and packings of non-shrinkable grains, little is known about how packings of shrinkable grains crack. Here, we elucidate how grain shrinkage alters cracking during drying. Using experiments with model shrinkable hydrogel beads, we show that differential shrinkage can dramatically alter crack evolution during drying---in some cases, even causing cracks to spontaneously self-close. In other cases, packings shrink without cracking or crack irreversibly. We developed both granular and continuum models to quantify the interplay between grain shrinkage, poromechanics, packing size, drying rate, capillarity, and substrate friction on cracking. Guided by the theory, we also found that cracking can be completely altered by varying the spatial profile of drying. Our work elucidates the rich physics underlying cracking in shrinkable, granular packings, and yields new strategies for controlling crack evolution.
The understanding of sliding friction for wet, patterned surfaces from first principles is challenging. While emerging applications have sought design principles from biology, a general framework is lacking because soft interfaces experience a multip
hysics coupling between solid deformation and fluid dissipation. We investigate the elastohydrodynamic sliding of >50 patterned sliding pairs comprising elastomers, thermosets, and hydrogels, and discover that texturing induces a critical transition in the macroscopic friction coefficient. This critical friction scales universally, without any fitting parameters, with the reduced elastic modulus and the pattern geometry. To capture the frictional dissipation, we separate the flow curve into two regimes and account for the contributions of shear and normal forces applied by the fluid on the patterns. Our model combines Reynolds equations and elastic deformation to provide physical insights that allow engineering of the elastohydrodynamic friction in a class of soft tribopairs using pattern geometry, material elasticity, and fluid properties.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
