اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدX-ray microtomography of heavy microstructures: the case of Plasma-Sprayed Tungsten and Tungsten-Steel MMC
51
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this paper synchrotron microtomography on Plasma Sprayed Tungsten (PS-W) is presented and discussed. PS-W is a challenging material for microtomography since it exhibits a random porous network at different length-scales (from nanometers to micrometers) and is hardly penetrable by X-rays. Furthermore, inner porosity causes strong internal scattering. The key challenges were, firstly, to optimize the beam parameters considering the inherent trade-off between photon energy (penetration depth) and spatial resolution and, secondly, to develop effective signal filtering algorithms. Despite the limited signal-to-noise ratio detected, large volumes of PS-W could be reconstructed with good image quality and micrometric resolution (voxel size = 1.4 {mu}m). As an important result, we report excellent image quality and higher penetration depth by applying the same setup on a ferrous microstructure, namely a 10%W/Steel MMC used as interlayer between PS-W and a ferritic/martensitic steel substrate. The paper reports a detailed 3D morphological analysis of all inclusion types in PS-W and W/Steel, which led to disclosure of a complex connected porous network in both media. The analysis is presented in terms of multiphase volume fraction, ratio of percolation and 3D shape descriptors. 3D percolation patterns are analyzed in detail and sensitivity towards segmentation threshold for the noise-affected PS-W region is discussed. Remarkably, percolation of the porous phase was found throughout the entire coating thickness of PS-W. In W-Steel MMC percolation was found in the perpendicular plane and interpreted as onset of delamination caused by thermomechanical stress.
قيم البحث
اقرأ أيضاً
In this work, we investigate the correlation between morphology, composition, and the mechanical properties of metallic amorphous tungsten-oxygen and amorphous tungsten-oxide films deposited by Pulsed Laser Deposition. This correlation is investigate
d by the combined use of Brillouin Spectroscopy and the substrate curvature method. The stiffness of the films is strongly affected by both the oxygen content and the mass density. The elastic moduli show a decreasing trend as the mass density decreases and the oxygen-tungsten ratio increases. A plateaux region is detected in correspondence of the transition between metallic and oxide films. The compressive residual stresses, moderate stiffness and high local ductility that characterize compact amorphous tungsten-oxide films make them promising for applications involving thermal or mechanical loads. The coefficient of thermal expansion is quite high (i.e. 8.9 $cdot$ 10$^{-6}$ K$^{-1}$), being strictly correlated to the amorphous structure and stoichiometry of the films. Under thermal treatments they show a quite low relaxation temperature (i.e. 450 K). They crystallize into the $gamma$ monoclinic phase of WO$_3$ starting from 670 K, inducing an increase by about 70% of material stiffness.
Deuterium(D) retention behavior in tungsten(W) exposed to deuterium plasma and gas was studied by means of thermal desorption spectroscopy (TDS): deuterium plasma exposure in which W was exposed to D plamsa with 35 eV/D at 393 K to the fluence of 3.8
E24 D/m2; D2 gas charging in which W was exposed to D2 gas of 500 kPa at 773 K for 4 hours. TDS shows that the total D retention in plasma exposure W is 1.00E22 D/m2, one order of magnitude higher than that of gas charging W; however, the D2 desorption peak of gas charging W is 952 K, much higher than 691 K of plasma exposure W. The detrapping energies of deuterium were determined experimentally from the measured peak temperatures at different heating rates and were found to be 2.17 eV for gas charging W and 1.04 eV for plasma exposure W, respectively.
Electrochromic devices, which dynamically change color under the applied potential, are widely studied because of its wide range of applications such as energy-efficient smart windows, rear view mirrors and display devices etc. In this study we are r
eporting four layer electrochromic device based on tungsten oxide as a electrochromic layer and nafion membrane as a ionic conducting layer. Nafion membranes are generally used in fuel cell applications because of its high ionic conductivity and high optical transparency which is suitable for electrochromic device to attain higher efficiencies. We have prepared an electrochromic device by sandwiching ITO coated glass and WO3 coated ITO thin film between nafion membrane. The overall structure of the device is Glass/ITO/WO3/Nafion/ITO/Glass. We deposited tungsten oxide thin films with different thickness on ITO coated glass substrate at room temperature by using reactive DC Magnetron sputtering and we studied the performance of the electrochromic device with the function of thickness. We have observed that electrochromic efficiency is increasing with increase in the tungsten oxide layer thickness. The efficiency of the device increased from 24.8 cm2/C to 184.3 cm2/C.
Tungsten is the main candidate material for plasma-facing armour components in future fusion reactors. Bombardment with energetic fusion neutrons causes collision cascade damage and defect formation. Interaction of defects with helium, produced by tr
ansmutation and injected from the plasma, modifies defect retention and behaviour. Here we investigate the residual lattice strains caused by different doses of helium-ion-implantation into tungsten and tungsten-rhenium alloys. Energy and depth-resolved synchrotron X-ray micro-diffraction uniquely permits the measurement of lattice strain with sub-micron 3D spatial resolution and ~10-4 strain sensitivity. Increase of helium dose from 300 appm to 3000 appm increases volumetric strain by only ~2.4 times, indicating that defect retention per injected helium atom is ~3 times higher at low helium doses. This suggests that defect retention is not a simple function of implanted helium dose, but strongly depends on material composition and presence of impurities. Conversely, analysis of W-1wt% Re alloy samples and of different crystal orientations shows that both the presence of rhenium, and crystal orientation, have comparatively small effect on defect retention. These insights are key for the design of armour components in future reactors where it will be essential to account for irradiation-induced dimensional change when predicting component lifetime and performance.
A lack of spatial inversion symmetry gives rise to a variety of unconventional physics, from noncollinear order and Skyrmion lattice phases in magnetic materials to topologically-protected surface states in certain band insulators, to mixed-parity pa
iring states in superconductors. The search for exotic physics in such materials is largely limited by a lack of candidate materials, and often by difficulty in obtaining crystals. Here, we report the single crystal growth and physical properties of the noncentrosymmetric tungsten aluminide cage compounds Al$_4$W and Al$_5$W, alongside related molybdenum aluminides in which spin-orbit coupling should be significantly weaker. All compounds are nonmagnetic metals. Their high conductivities suggest the opportunity to find superconductivity at lower temperatures, while the limits we can place on their transition temperatures suggest that any superconductivity may be expected to exhibit significant parity mixing.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
