اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدModel Predictive Control under Timing Constraints induced by Controller Area Networks
256
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
When multiple model predictive controllers are implemented on a shared control area network (CAN), their performance may degrade due to the inhomogeneous timing and delays among messages. The priority based real-time scheduling of messages on the CAN introduces complex timing of events, especially when the types and number of messages change at runtime. This paper introduces a novel hybrid timing model to make runtime predictions on the timing of the messages for a finite time window. Controllers can be designed using the optimization algorithms for model predictive control by considering the timing as optimization constraints. This timing model allows multiple controllers to share a CAN without significant degradation in the controller performance. The timing model also provides a convenient way to check the schedulability of messages on the CAN at runtime. Simulation results demonstrate that the timing model is accurate and computationally efficient to meet the needs of real-time implementation. Simulation results also demonstrate that model predictive controllers designed when considering the timing constraints have superior performance than the controllers designed without considering the timing constraints.
قيم البحث
اقرأ أيضاً
Diesel airpath controllers are required to deliver good tracking performance whilst satisfying operational constraints and physical limitations of the actuators. Due to explicit constraint handling capabilities, model predictive controllers (MPC) hav
e been successfully deployed in diesel airpath applications. Previous MPC implementations have considered instantaneous constraints on engine-out emissions in order to meet legislated emissions regulations. However, the emissions standards are specified over a drive cycle, and hence, can be satisfied on average rather than just instantaneously, potentially allowing the controller to exploit the trade-off between emissions and fuel economy. In this work, an MPC is formulated to maximise the fuel efficiency whilst tracking boost pressure and exhaust gas recirculation (EGR) rate references, and in the face of uncertainties, adhering to the input, safety constraints and constraints on emissions averaged over some finite time period. The tracking performance and satisfaction of average emissions constraints using the proposed controller are demonstrated through an experimental study considering the new European drive cycle.
Trajectory optimization of a controlled dynamical system is an essential part of autonomy, however many trajectory optimization techniques are limited by the fidelity of the underlying parametric model. In the field of robotics, a lack of model knowl
edge can be overcome with machine learning techniques, utilizing measurements to build a dynamical model from the data. This paper aims to take the middle ground between these two approaches by introducing a semi-parametric representation of the underlying system dynamics. Our goal is to leverage the considerable information contained in a traditional physics based model and combine it with a data-driven, non-parametric regression technique known as a Gaussian Process. Integrating this semi-parametric model with model predictive pseudospectral control, we demonstrate this technique on both a cart pole and quadrotor simulation with unmodeled damping and parametric error. In order to manage parametric uncertainty, we introduce an algorithm that utilizes Sparse Spectrum Gaussian Processes (SSGP) for online learning after each rollout. We implement this online learning technique on a cart pole and quadrator, then demonstrate the use of online learning and obstacle avoidance for the dubin vehicle dynamics.
A significant challenge in the development of control systems for diesel airpath applications is to tune the controller parameters to achieve satisfactory output performance, especially whilst adhering to input and safety constraints in the presence
of unknown system disturbances. Model-based control techniques, such as model predictive control (MPC), have been successfully applied to multivariable and highly nonlinear systems, such as diesel engines, while considering operational constraints. However, efficient calibration of typical implementations of MPC is hindered by the high number of tuning parameters and their non-intuitive correlation with the output response. In this paper, the number of effective tuning parameters is reduced through suitable structural modifications to the controller formulation and an appropriate redesign of the MPC cost function to aid rapid calibration. Furthermore, a constraint tightening-like approach is augmented to the control architecture to provide robustness guarantees in the face of uncertainties. A switched linear time-varying MPC strategy with recursive feasibility guarantees during controller switching is proposed to handle transient operation of the engine. The robust controller is first implemented on a high fidelity simulation environment, with a comprehensive investigation of its calibration to achieve desired transient response under step changes in the fuelling rate. An experimental study then validates and highlights the performance of the proposed controller architecture for selected tunings of the calibration parameters for fuelling steps and over drive cycles.
A stochastic model predictive control (SMPC) approach is presented for discrete-time linear systems with arbitrary time-invariant probabilistic uncertainties and additive Gaussian process noise. Closed-loop stability of the SMPC approach is establish
ed by appropriate selection of the cost function. Polynomial chaos is used for uncertainty propagation through system dynamics. The performance of the SMPC approach is demonstrated using the Van de Vusse reactions.
We present an algorithm for controlling and scheduling multiple linear time-invariant processes on a shared bandwidth limited communication network using adaptive sampling intervals. The controller is centralized and computes at every sampling instan
t not only the new control command for a process, but also decides the time interval to wait until taking the next sample. The approach relies on model predictive control ideas, where the cost function penalizes the state and control effort as well as the time interval until the next sample is taken. The latter is introduced in order to generate an adaptive sampling scheme for the overall system such that the sampling time increases as the norm of the system state goes to zero. The paper presents a method for synthesizing such a predictive controller and gives explicit sufficient conditions for when it is stabilizing. Further explicit conditions are given which guarantee conflict free transmissions on the network. It is shown that the optimization problem may be solved off-line and that the controller can be implemented as a lookup table of state feedback gains. Simulation studies which compare the proposed algorithm to periodic sampling illustrate potential performance gains.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
