اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدE-BLOW: E-Beam Lithography Overlapping aware Stencil Planning for MCC System
120
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Electron beam lithography (EBL) is a promising maskless solution for the technology beyond 14nm logic node. To overcome its throughput limitation, recently the traditional EBL system is extended into MCC system. %to further improve the throughput. In this paper, we present E-BLOW, a tool to solve the overlapping aware stencil planning (OSP) problems in MCC system. E-BLOW is integrated with several novel speedup techniques, i.e., successive relaxation, dynamic programming and KD-Tree based clustering, to achieve a good performance in terms of runtime and solution quality. Experimental results show that, compared with previous works, E-BLOW demonstrates better performance for both conventional EBL system and MCC system.
قيم البحث
اقرأ أيضاً
Layout fracturing is a fundamental step in mask data preparation and e-beam lithography (EBL) writing. To increase EBL throughput, recently a new L-shape writing strategy is proposed, which calls for new L-shape fracturing, versus the conventional re
ctangular fracturing. Meanwhile, during layout fracturing, one must minimize very small/narrow features, also called slivers, due to manufacturability concern. This paper addresses this new research problem of how to perform L-shaped fracturing with sliver minimization. We propose two novel algorithms. The first one, rectangular merging (RM), starts from a set of rectangular fractures and merges them optimally to form L-shape fracturing. The second algorithm, direct L-shape fracturing (DLF), directly and effectively fractures the input layouts into L-shapes with sliver minimization. The experimental results show that our algorithms are very effective.
We present a novel shadow evaporation technique for the realization of junctions and capacitors. The design by E-beam lithography of strongly asymmetric undercuts on a bilayer resist enables in-situ fabrication of junctions and capacitors without the
use of the well-known suspended bridge[1]. The absence of bridges increases the mechanical robustness of the resist mask as well as the accessible range of the junction size, from 0.01 to more than 10000 micron square. We have fabricated Al/AlOx/Al Josephson junctions, phase qubit and capacitors using a 100kV E- beam writer. Although this high voltage enables a precise control of the undercut, implementation using a conventional 20kV E-beam is also discussed. The phase qubit coherence times, extracted from spectroscopy resonance width, Rabi and Ramsey oscillations decay and energy relaxation measurements, are longer than the ones obtained in our previous samples realized by standard techniques. These results demonstrate the high quality of the junction obtained by this controlled undercut technique.
A combined bottom-up assembly of electrodeposited nanowires and electron beam lithography technique has been developed to investigate the spin transfer torque and microwave emission on specially designed nanowires containing a single Co/Cu/Co pseudo
spin valve. Microwave signals have been obtained even at zero magnetic field. Interestingly, high frequency vs. magnetic field tunability was demonstrated, in the range 0.4 - 2 MHz/Oe, depending on the orientation of the applied magnetic field relative to the magnetic layers of the pseudo spin valve. The frequency values and the emitted signal frequency as a function of the external magnetic field are in good quantitative agreement with the analytical vortex model as well as with micromagnetic simulations.
We perform a beam-beam parameter study for a TeV-scale PWFA (particle-driven plasma wakefield acceleration) $mathrm{e}^+$$mathrm{e}^-$ linear collider using GUINEA-PIG simulations. The study shows that the total luminosity follows the $1/sqrt{sigma_z
}$-scaling predicted by beamstrahlung theory, where $sigma_z$ is the rms beam length, which is advantageous for PWFA, as short beam lengths are preferred. We also derive a parameter set for a 3 TeV PWFA linear collider with main beam parameters optimised for luminosity and luminosity spread introduced by beamstrahlung. Lastly, the study also compare the performance for scenarios with reduced positron beam charge at 3 TeV and 14 TeV with CLIC parameters.
We calculate the single spin asymmetry for the $e p to e Delta(1232)$ process, for an electron beam polarized normal to the scattering plane. Such single spin asymmetries vanish in the one-photon exchange approximation, and are directly proportional
to the absorptive part of a two-photon exchange amplitude. As the intermediate state in such two-photon exchange process is on its mass shell, the asymmetry allows one to access for the first time the on-shell $Delta to Delta$ as well as $N^ast to Delta$ electromagnetic transitions. We present the general formalism to describe the $e p to e Delta$ beam normal spin asymmetry, and provide a numerical estimate of its value using the nucleon, $Delta(1232)$, $S_{11}(1535)$, and $D_{13}(1520)$ intermediate states. We compare our results with the first data from the Qweak@JLab experiment and give predictions for the A4@MAMI experiment.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
