اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدNovel E-beam lithography technique for in-situ junction fabrication: the controlled undercut
112
0
0.0
(
0
)
تأليف
Florent Lecocq
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We present a novel shadow evaporation technique for the realization of junctions and capacitors. The design by E-beam lithography of strongly asymmetric undercuts on a bilayer resist enables in-situ fabrication of junctions and capacitors without the use of the well-known suspended bridge[1]. The absence of bridges increases the mechanical robustness of the resist mask as well as the accessible range of the junction size, from 0.01 to more than 10000 micron square. We have fabricated Al/AlOx/Al Josephson junctions, phase qubit and capacitors using a 100kV E- beam writer. Although this high voltage enables a precise control of the undercut, implementation using a conventional 20kV E-beam is also discussed. The phase qubit coherence times, extracted from spectroscopy resonance width, Rabi and Ramsey oscillations decay and energy relaxation measurements, are longer than the ones obtained in our previous samples realized by standard techniques. These results demonstrate the high quality of the junction obtained by this controlled undercut technique.
قيم البحث
اقرأ أيضاً
Self-organized semiconductor quantum dots represent almost ideal two-level systems, which have strong potential to applications in photonic quantum technologies. For instance, they can act as emitters in close-to-ideal quantum light sources. Coupled
quantum dot systems with significantly increased functionality are potentially of even stronger interest since they can be used to host ultra-stable singlet-triplet spin qubits for efficient spin-photon interfaces and for a deterministic photonic 2D cluster-state generation. We realize an advanced quantum dot molecule (QDM) device and demonstrate excellent optical properties. The device includes electrically controllable QDMs based on stacked quantum dots in a pin-diode structure. The QDMs are deterministically integrated into a photonic structure with a circular Bragg grating using in-situ electron beam lithography. We measure a photon extraction efficiency of up to (24$pm$4)% in good agreement with numerical simulations. The coupling character of the QDMs is clearly demonstrated by bias voltage dependent spectroscopy that also controls the orbital couplings of the QDMs and their charge state in quantitative agreement with theory. The QDM devices show excellent single-photon emission properties with a multi-photon suppression of $g^{(2)}(0) = (3.9 pm 0.5) cdot 10^{-3}$. These metrics make the developed QDM devices attractive building blocks for use in future photonic quantum networks using advanced nanophotonic hardware.
We have combined direct nanofabrication by local anodic oxidation with conventional electron-beam lithography to produce a parallel double quantum dot based on a GaAs/AlGaAs heterostructure. The combination of both nanolithography methods allows to f
abricate robust in-plane gates and Cr/Au top gate electrodes on the same device for optimal controllability. This is illustrated by the tunability of the interdot coupling in our device. We describe our fabrication and alignment scheme in detail and demonstrate the tunability in low-temperature transport measurements.
Lithographically fabricated point contacts serve as important examples of mesoscopic conductors, as electrodes for molecular electronics, and as ultra-sensitive transducers for mechanical motion. We have developed a reproducible technique for fabrica
ting metallic point contacts though electromigration. We employ fast analog feedback in a four-wire configuration in combination with slower computer controlled feedback to avoid catastrophic instability. This hybrid system allows electromigration to proceed while dissipating approximately constant power in the wire. We are able to control the final resistance of the point contact precisely below 5 kOmega and to within a factor of three when the target resistance approaches 12 kOmega where only a single conducting channel remains.
We have developed a controlled and highly reproducible method of making nanometer-spaced electrodes using electromigration in ambient lab conditions. This advance will make feasible single molecule measurements of macromolecules with tertiary and qua
ternary structures that do not survive the liquid-helium temperatures at which electromigration is typically performed. A second advance is that it yields gaps of desired tunnelling resistance, as opposed to the random formation at liquid-helium temperatures. Nanogap formation occurs through three regimes: First it evolves through a bulk-neck regime where electromigration is triggered at constant temperature, then to a few-atom regime characterized by conductance quantum plateaus and jumps, and finally to a tunnelling regime across the nanogap once the conductance falls below the conductance quantum.
We present a technique to fabricate ultrathin (down to 20 nm) uniform electron transparent windows at dedicated locations in a SiN membrane for in situ transmission electron microscopy experiments. An electron-beam (e-beam) resist is spray-coated on
the backside of the membrane in a KOH- etched cavity in silicon which is patterned using through-membrane electron-beam lithography. This is a controlled way to make transparent windows in membranes, whilst the topside of the membrane remains undamaged and retains its flatness. Our approach was optimized for MEMS-based heating chips but can be applied to any chip design. We show two different applications of this technique for (1) fabrication of a nanogap electrode by means of electromigration in thin free-standing metal films and (2) making low-noise graphene nanopore devices.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
