اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدRectangular and Circular Antenna Design on Thick Substrate
101
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Millimeter wave technology being an emerging area is still very undeveloped. A substantial research needs to be done in this area as its applications are numerous. In the present endeavor, a rectangular patch antenna is designed on thick substrate and simulated using SONNET software, also a novel analysis technique is developed for circular patch antenna for millimeter wave frequency. The antenna is designed at 39 GHz on thick substrate and has been analyzed and simulated.The results of the theoretical analysis are in good agreement with the simulated results.
قيم البحث
اقرأ أيضاً
In this paper, a single layer Coplanar Waveguide-fed microstrip patch antenna array is presented for biomedical applications. The proposed antenna array is realized on a transparent and flexible Polyethylene Terephthalate substrate, has 1x4 radiating
elements and measures only 280 x 192 mm2. The antenna array resonates at 2.68 GHz and has a peak-simulated gain of 10 dBi. A prototype is also fabricated, and the conductive patterns are drawn using cost-efficient adhesive copper foils instead of conventional copper or silver nanoparticle ink. The corresponding measured results agree well with the simulated results. The proposed low profile and cost-efficient transmit antenna array has the potential for wearable born-worn applications, including wireless powering of implantable medical devices.
In this paper, the bulge test is used to determine the mechanical properties of very thin dielectric membranes. Commonly, this experimental method permits to determine the residual stress (s0) and biaxial Youngs modulus (E/(1-u)). Associating square
and rectangular membranes with different length to width ratios, the Poissons ratio (u) can also be determined. LPCVD Si3N4 monolayer and Si3N4/SiO2 bilayer membranes, with thicknesses down to 100 nm, have been characterized giving results in agreement with literature for Si3N4, E = 212 $pm$ 14 GPa, s0 = 420 $pm$ 8 and u = 0.29.
A novel and compact dual band dual sense circularly polarized microstrip patch antenna with single coaxial feed has been reported in the present work. The key idea of generating dual band circular polarisation (CP) is the integration of a square patc
h with corner truncation and a smaller concentric circular patch with double slits. The first resonance is provided by the larger patch whose corner truncation generates two orthogonal modes. The inner patch controls the higher-order resonance with the CP contributed by two narrow slits. The higher order resonating frequency can be monitored by controlling the dimensions of the circle and the slits. The antenna provides the CP in two orthogonal planes with two different sense of polarisation. The lower order CP is of left-handed orientation, whereas the higher order shows right-handed polarization. The cross-polarization level is also found to be very low.
The Bienenstock-Cooper-Munro (BCM) and Spike Timing-Dependent Plasticity (STDP) rules are two experimentally verified form of synaptic plasticity where the alteration of synaptic weight depends upon the rate and the timing of pre- and post-synaptic f
iring of action potentials, respectively. Previous studies have reported that under specific conditions, i.e. when a random train of Poissonian distributed spikes are used as inputs, and weight changes occur according to STDP, it has been shown that the BCM rule is an emergent property. Here, the applied STDP rule can be either classical pair-based STDP rule, or the more powerful triplet-based STDP rule. In this paper, we demonstrate the use of two distinct VLSI circuit implementations of STDP to examine whether BCM learning is an emergent property of STDP. These circuits are stimulated with random Poissonian spike trains. The first circuit implements the classical pair-based STDP, while the second circuit realizes a previously described triplet-based STDP rule. These two circuits are simulated using 0.35 um CMOS standard model in HSpice simulator. Simulation results demonstrate that the proposed triplet-based STDP circuit significantly produces the threshold-based behaviour of the BCM. Also, the results testify to similar behaviour for the VLSI circuit for pair-based STDP in generating the BCM.
This paper presents one MEMS design tool with total six design flows, which makes it possible that the MEMS designers are able to choose the most suitable design flow for their specific devices. The design tool is divided into three levels and interc
onnected by six interfaces. The three levels are lumped-element model based system level, finite element analysis based device level and process level, which covers nearly all modeling and simulation functions for MEMS design. The six interfaces are proposed to automatically transmit the design data between every two levels, thus the maximal six design flows could be realized. The interfaces take the netlist, solid model and layout as the data inlet and outlet for the system, device and process level respectively. The realization of these interfaces are presented and verified by design examples, which also proves that the enough flexibility in the design flow can really increase the design efficiency.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
