Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userPrecision velocimetry planet hunting with PARAS: Current performance and lessons to inform future extreme precision radial velocity instruments
123
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
PARAS is a fiber-fed stabilized high-resolution cross-dispersed echelle spectrograph, located on the 1.2 m telescope in Mt. Abu India. Designed for exoplanet detection, PARAS is capable of single-shot spectral coverage of 3800 - 9600 A, and currently achieving radial velocity (RV) precisions approaching ~1 m/s over several months using simultaneous ThAr calibration. As such, it is one of the few dedicated stabilized fiber-fed spectrographs on small (1-2 m) telescopes that are able to fill an important niche in RV follow-up and stellar characterization. The success of ground-based RV surveys is motivating the push into extreme precisions, with goals of ~10 cm/s in the optical and <1 m/s in the near-infrared (NIR). Lessons from existing instruments like PARAS are invaluable in informing hardware design, providing pipeline prototypes, and guiding scientific surveys. Here we present our current precision estimates of PARAS based on observations of bright RV standard stars, and describe the evolution of the data reduction and RV analysis pipeline as instrument characterization progresses and we gather longer baselines of data. Secondly, we discuss how our experience with PARAS is a critical component in the development of future cutting edge instruments like (1) the Habitable Zone Planet Finder (HPF), a NIR spectrograph optimized to look for planets around M dwarfs, scheduled to be commissioned on the Hobby Eberly Telescope in 2017, and (2) the NEID optical spectrograph, designed in response to the NN-EXPLORE call for an extreme precision Doppler spectrometer (EPDS) for the WIYN telescope. In anticipation of instruments like TESS and GAIA, the ground-based RV support system is being reinforced. We emphasize that instruments like PARAS will play an intrinsic role in providing both complementary follow-up and battlefront experience for these next generation of precision velocimeters.
rate research
Read More
Precise mass measurements of exoplanets discovered by the direct imaging or transit technique are required to determine planet bulk properties and potential habitability. Furthermore, it is generally acknowledged that, for the foreseeable future, the Extreme Precision Radial Velocity (EPRV) measurement technique is the only method potentially capable of detecting and measuring the masses and orbits of habitable-zone Earths orbiting nearby F, G, and K spectral-type stars from the ground. In particular, EPRV measurements with a precision of better than approximately 10 cm/s (with a few cm/s stability over many years) are required. Unfortunately, for nearly a decade, PRV instruments and surveys have been unable to routinely reach RV accuracies of less than roughly 1 m/s. Making EPRV science and technology development a critical component of both NASA and NSF program plans is crucial for reaching the goal of detecting potentially habitable Earthlike planets and supporting potential future exoplanet direct imaging missions such as the Habitable Exoplanet Observatory (HabEx) or the Large Ultraviolet Optical Infrared Surveyor (LUVOIR). In recognition of these facts, the 2018 National Academy of Sciences (NAS) Exoplanet Science Strategy (ESS) report recommended the development of EPRV measurements as a critical step toward the detection and characterization of habitable, Earth-analog planets. In response to the NAS-ESS recommendation, NASA and NSF commissioned the EPRV Working Group to recommend a ground-based program architecture and implementation plan to achieve the goal intended by the NAS. This report documents the activities, findings, and recommendations of the EPRV Working Group.
The EXtreme PREcision Spectrograph (EXPRES) is an environmentally stabilized, fiber-fed, $R=137,500$, optical spectrograph. It was recently commissioned at the 4.3-m Lowell Discovery Telescope (LDT) near Flagstaff, Arizona. The spectrograph was designed with a target radial-velocity (RV) precision of 30$mathrm{~cm~s^{-1}}$. In addition to instrumental innovations, the EXPRES pipeline, presented here, is the first for an on-sky, optical, fiber-fed spectrograph to employ many novel techniques---including an extended flat fiber used for wavelength-dependent quantum efficiency characterization of the CCD, a flat-relative optimal extraction algorithm, chromatic barycentric corrections, chromatic calibration offsets, and an ultra-precise laser frequency comb for wavelength calibration. We describe the reduction, calibration, and radial-velocity analysis pipeline used for EXPRES and present an example of our current sub-meter-per-second RV measurement precision, which reaches a formal, single-measurement error of 0.3$mathrm{~m~s^{-1}}$ for an observation with a per-pixel signal-to-noise ratio of 250. These velocities yield an orbital solution on the known exoplanet host 51 Peg that matches literature values with a residual RMS of 0.895$mathrm{~m~s^{-1}}$.
Solar contamination, due to moonlight and atmospheric scattering of sunlight, can cause systematic errors in stellar radial velocity (RV) measurements that significantly detract from the ~10cm/s sensitivity required for the detection and characterization of terrestrial exoplanets in or near Habitable Zones of Sun-like stars. The addition of low-level spectral contamination at variable effective velocity offsets introduces systematic noise when measuring velocities using classical mask-based or template-based cross-correlation techniques. Here we present simulations estimating the range of RV measurement error induced by uncorrected scattered sunlight contamination. We explore potential correction techniques, using both simultaneous spectrometer sky fibers and broadband imaging via coherent fiber imaging bundles, that could reliably reduce this source of error to below the photon-noise limit of typical stellar observations. We discuss the limitations of these simulations, the underlying assumptions, and mitigation mechanisms. We also present and discuss the components designed and built into the NEID precision RV instrument for the WIYN 3.5m telescope, to serve as an ongoing resource for the community to explore and evaluate correction techniques. We emphasize that while bright time has been traditionally adequate for RV science, the goal of 10cm/s precision on the most interesting exoplanetary systems may necessitate access to darker skies for these next-generation instruments.
The EXtreme PREcision Spectrograph (EXPRES) is a new Doppler spectrograph designed to reach a radial velocity measurement precision sufficient to detect Earth-like exoplanets orbiting nearby, bright stars. We report on extensive laboratory testing and on-sky observations to quantitatively assess the instrumental radial velocity measurement precision of EXPRES, with a focused discussion of individual terms in the instrument error budget. We find that EXPRES can reach a single-measurement instrument calibration precision better than 10 cm/s, not including photon noise from stellar observations. We also report on the performance of the various environmental, mechanical, and optical subsystems of EXPRES, assessing any contributions to radial velocity error. For atmospheric and telescope related effects, this includes the fast tip-tilt guiding system, atmospheric dispersion compensation, and the chromatic exposure meter. For instrument calibration, this includes the laser frequency comb (LFC), flat-field light source, CCD detector, and effects in the optical fibers. Modal noise is mitigated to a negligible level via a chaotic fiber agitator, which is especially important for wavelength calibration with the LFC. Regarding detector effects, we empirically assess the impact on radial velocity precision due to pixel-position non-uniformities (PPNU) and charge transfer inefficiency (CTI). EXPRES has begun its science survey to discover exoplanets orbiting G-dwarf and K-dwarf stars, in addition to transit spectroscopy and measurements of the Rossiter-McLaughlin effect.
The Second Workshop on Extreme Precision Radial Velocities defined circa 2015 the state of the art Doppler precision and identified the critical path challenges for reaching 10 cm/s measurement precision. The presentations and discussion of key issues for instrumentation and data analysis and the workshop recommendations for achieving this precision are summarized here. Beginning with the HARPS spectrograph, technological advances for precision radial velocity measurements have focused on building extremely stable instruments. To reach still higher precision, future spectrometers will need to produce even higher fidelity spectra. This should be possible with improved environmental control, greater stability in the illumination of the spectrometer optics, better detectors, more precise wavelength calibration, and broader bandwidth spectra. Key data analysis challenges for the precision radial velocity community include distinguishing center of mass Keplerian motion from photospheric velocities, and the proper treatment of telluric contamination. Success here is coupled to the instrument design, but also requires the implementation of robust statistical and modeling techniques. Center of mass velocities produce Doppler shifts that affect every line identically, while photospheric velocities produce line profile asymmetries with wavelength and temporal dependencies that are different from Keplerian signals. Exoplanets are an important subfield of astronomy and there has been an impressive rate of discovery over the past two decades. Higher precision radial velocity measurements are required to serve as a discovery technique for potentially habitable worlds and to characterize detections from transit missions. The future of exoplanet science has very different trajectories depending on the precision that can ultimately be achieved with Doppler measurements.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
