Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userPhotonic bands and defect modes in metallo-dielectric photonic crystal slabs
89
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Photonic components based on structured metallic elements show great potential for device applications where field enhancement and confinement of the radiation on a subwavelength scale is required. In this paper we report a detailed study of a prototypical metallo-dielectric photonic structure, where features well known in the world of dielectric photonic crystals, like band gaps and defect modes, are exported to the metallic counterpart, with interesting applications to infrared science and technology, as for instance in quantum well infrared photodetectors, narrow-band spectral filters, and tailorable thermal emitters.
rate research
Read More
Photonic crystals with a finite size can support surface modes when appropriately terminated. We calculate the dispersion curves of surface modes for different terminations using the plane wave expansion method. These non-radiative surface modes can be excited with the help of attenuated total reflection technique. We did experiments and simulations to trace the surface band curve, both in good agreement with the numerical calculations.
We experimentally and theoretically investigate the second order nonlinear optical response of metallo-dielectric multilayer structures composed of Ag and Ta2O5 layers, deposited by magnetron sputtering. Second harmonic generation measurements were performed in reflection mode as a function of incidence angle, using femtosecond pulses originating from a Ti:Sapphire laser system tuned at 800 nm. The dependence of the generated signal was investigated as a function of pump intensity and polarization state. Our experimental results show that the conversion efficiency from a periodic metallo-dielectric sample may be enhanced by at least a factor of 30 with respect to the conversion efficiency from a single metal layer, thanks in part to the increased number of active surfaces, pump field localization and penetration inside the metal layers. The conversion efficiency maximum shifts from 70 degrees for the single silver layer down to approximately 55 degrees for the stack. The experimental results are found to be in good agreement with calculations based on coupled Maxwell-Drude oscillators under the action of a nonlinear Lorentz force term.
A finite element-based modal formulation of diffraction of a plane wave by an absorbing photonic crystal slab of arbitrary geometry is developed for photovoltaic applications. The semi-analytic approach allows efficient and accurate calculation of the absorption of an array with a complex unit cell. This approach gives direct physical insight into the absorption mechanism in such structures, which can be used to enhance the absorption. The verification and validation of this approach is applied to a silicon nanowire array and the efficiency and accuracy of the method is demonstrated. The method is ideally suited to studying the manner in which spectral properties (e.g., absorption) vary with the thickness of the array, and we demonstrate this with efficient calculations which can identify an optimal geometry.
We perform phase-sensitive near-field scanning optical microscopy on photonic-crystal waveguides. The observed intricate field patterns are analyzed by spatial Fourier transformations, revealing several guided TE- and TM-like modes. Using the reconstruction algorithm proposed by Ha, et al. (Opt. Lett. 34 (2009)), we decompose the measured two-dimensional field pattern in a superposition of propagating Bloch modes. This opens new possibilities to study specific modes in near-field measurements. We apply the method to study the transverse behavior of a guided TE-like mode, where the mode extends deeper in the surrounding photonic crystal when the band edge is approached.
Higher-order modes up to LP$_{33}$ are controllably excited in water-filled kagom{e}- and bandgap-style hollow-core photonic crystal fibers (HC-PCF). A spatial light modulator is used to create amplitude and phase distributions that closely match those of the fiber modes, resulting in typical launch efficiencies of 10-20% into the liquid-filled core. Modes, excited across the visible wavelength range, closely resemble those observed in air-filled kagom{e} HC-PCF and match numerical simulations. Mode indices are obtained by launching plane-waves at specific angles onto the fiber input-face and comparing the resulting intensity pattern to that of a particular mode. These results provide a framework for spatially-resolved sensing in HC-PCF microreactors and fiber-based optical manipulation.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
