Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userVortex-assisted photon counts and their magnetic field dependence in single-photon detectors
464
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We argue that photon counts in a superconducting nanowire single-photon detector (SNSPD) are caused by the transition from a current-biased metastable superconducting state to the normal state. Such a transition is triggered by vortices crossing the thin film superconducting strip from one edge to another due to the Lorentz force. Detector counts in SNSPDs may be caused by three processes: (a) a single incident photon with energy sufficient to break enough Cooper pairs to create a normal-state belt across the entire width of the strip (direct photon count), (b) thermally induced single-vortex crossing in the absence of photons (dark count), which at high bias currents releases the energy sufficient to trigger the transition to the normal state in a belt across the whole width of the strip, and (c) a single incident photon with insufficient energy to create a normal-state belt but initiating a subsequent single-vortex crossing, which provides the rest of the energy needed to create the normal-state belt (vortex-assisted single photon count). We derive the current dependence of the rate of vortex-assisted photon counts. The resulting photon count rate has a plateau at high currents close to the critical current and drops as a power-law with high exponent at lower currents. While the magnetic field perpendicular to the film plane does not affect the formation of hot spots by photons, it causes the rate of vortex crossings (with or without photons) to increase. We show that by applying a magnetic field one may characterize the energy barrier for vortex crossings and identify the origin of dark counts and vortex-assisted photon counts.
rate research
Read More
We argue that cutoff in the London model cannot be settled without use of the microscopic theory.
In this Comment we show that the statements made in PRB85, 014505 (2012) regarding our work (PRL 100, 227007 (2008))) are incorrect because they result from model artifacts. We address the issues neglected in PRB85, 014505 (2012) and discuss their importance for a more consistent theory of thermally-activated hoping of vortices in thin films and the interpretation of experimental data.
We investigate the role of electrothermal feedback in the operation of superconducting nanowire single-photon detectors (SNSPDs). It is found that the desired mode of operation for SNSPDs is only achieved if this feedback is unstable, which happens naturally through the slow electrical response associated with their relatively large kinetic inductance. If this response is sped up in an effort to increase the device count rate, the electrothermal feedback becomes stable and results in an effect known as latching, where the device is locked in a resistive state and can no longer detect photons. We present a set of experiments which elucidate this effect, and a simple model which quantitatively explains the results.
We use external magnetic field to probe the detection mechanism of superconducting nanowire single photon detector. We argue that the hot belt model (which assumes partial suppression of the superconducting order parameter $Delta$ across the whole width of the superconducting nanowire after absorption of the single photon) does not explain observed weak field dependence of the photon count rate (PCR) for photons with $lambda$=450 nm and noticeable {it decrease} of PCR (with increasing the magnetic field) in some range of the currents for photons with wavelengths $lambda$ =450-1200 nm. Found experimental results for all studied wavelengths $lambda = 450-1550$ nm could be explained by the vortex hot spot model (which assumes partial suppression of $Delta$ in the area with size smaller than the width of the nanowire) if one takes into account nucleation and entrance of the vortices to the photon induced hot spot and their pinning by the hot spot with relatively large size and strongly suppressed $Delta$.
We report measurements of the energy resolution of ultra-sensitive superconducting bolometric detectors. The device is a superconducting titanium nanobridge with niobium contacts. A fast microwave pulse is used to simulate a single higher-frequency photon, where the absorbed energy of the pulse is equal to the photon energy. This technique allows precise calibration of the input coupling and avoids problems with unwanted background photons. Present devices have an intrinsic full-width at half-maximum energy resolution of approximately 23 terahertz, near the predicted value due to intrinsic thermal fluctuation noise.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
