Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userDissipation in Single-Crystal 3C-SiC Ultra-High Frequency Nanomechanical Resonators
185
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The energy dissipation 1/Q (where Q is the quality factor) and resonance frequency characteristics of single-crystal 3C-SiC ultrahigh frequency (UHF) nanomechanical resonators are measured, for a family of UHF resonators with resonance frequencies of 295MHz, 395MHz, 411MHz, 420MHz, 428MHz, and 482MHz. A temperature dependence of dissipation, 1/Q ~ T^(0.3) has been identified in these 3C-SiC devices. Possible mechanisms that contribute to dissipation in typical doubly-clamped beam UHF resonators are analyzed. Device size and dimensional effects on the dissipation are also examined. Clamping losses are found to be particularly important in these UHF resonators. The resonance frequency decreases as the temperature is increased, and the average frequency temperature coefficient is about -45ppm/K.
rate research
Read More
We have studied damping in polycrystalline Al nanomechanical resonators by measuring the temperature dependence of their resonance frequency and quality factor over a temperature range of 0.1 - 4 K. Two regimes are clearly distinguished with a crossover temperature of 1 K. Below 1 K we observe a logarithmic temperature dependence of the frequency and linear dependence of damping that cannot be explained by the existing standard models. We attribute these phenomena to the effect of the two-level systems characterized by the unexpectedly long (at least two orders of magnitude longer) relaxation times and discuss possible microscopic models for such systems. We conclude that the dynamics of the two-level systems is dominated by their interaction with one-dimensional phonon modes of the resonators.
We describe the measurement and modeling of amplitude noise and phase noise in ultra-high Q nanomechanical resonators made from stoichiometric silicon nitride. With quality factors exceeding 2 million, the resonators noise performance is studied with high precision. We find that the amplitude noise can be well described by the thermomechanical model, however, the resonators exhibit sizable extra phase noise due to their intrinsic frequency fluctuations. We develop a method to extract the resonator frequency fluctuation of a driven resonator and obtain a noise spectrum with dependence, which could be attributed to defect motion with broadly distributed relaxation times.
In strained mechanical resonators, the concurrence of tensile stress and geometric nonlinearity dramatically reduces dissipation. This phenomenon, dissipation dilution, is employed in mirror suspensions of gravitational wave interferometers and at the nanoscale, where soft-clamping and strain engineering have allowed extremely high quality factors. However, these techniques have so far only been applied in amorphous materials, specifically silicon nitride. Crystalline materials exhibit significantly lower intrinsic damping at cryogenic temperatures, due to the absence of two level systems in the bulk, as exploited in Weber bars and silicon optomechanical cavities. Applying dissipation dilution engineering to strained crystalline materials could therefore enable extremely low loss nanomechanical resonators, due to the combination of reduced internal friction, high intrinsic strain, and high yield strength. Pioneering work has not yet fully exploited this potential. Here, we demonstrate that single crystal strained silicon, a material developed for high mobility transistors, can be used to realize mechanical resonators with ultralow dissipation. We observe that high aspect ratio ($>10^5$) strained silicon nanostrings support MHz mechanical modes with quality factors exceeding $10^{10}$ at 7 K, a tenfold improvement over values reported in silicon nitride. At 7 K, the thermal noise-limited force sensitivity is approximately $45 mathrm{{zN}/{sqrt{Hz}}}$ - approaching that of carbon nanotubes - and the heating rate is only 60 quanta-per-second. Our nanomechanical resonators exhibit lower dissipation than the most pristine macroscopic oscillators and their low mass makes them particularly promising for quantum sensing and transduction.
We present nanofabrication and mechanical measurements of single-crystal diamond cantilevers with thickness down to 85 nm, thickness uniformity better than 20 nm, and lateral dimensions up to 240 um. Quality factors exceeding one million are found at room temperature, surpassing those of state-of-the-art single-crystal silicon cantilevers of similar dimensions by roughly an order of magnitude. Force sensitivities of a few hundred zeptonewtons result for the best cantilevers at millikelvin temperatures. Single-crystal diamond could thus directly improve existing force and mass sensors by a simple substitution of resonator material, and lead to quantum nanomechanical devices with exceptionally low energy dissipation.
State of the art nanomechanical resonators present quality factors Q ~ 10^3 - 10^5, which are much lower than those that can be naively extrapolated from the behavior of micromechanical resonators. We analyze the dissipation mechanism that arises in nanomechanical beam-structures due to the tunneling of mesoscopic phonons between the beam and its supports (known as clamping losses). We derive the environmental force spectral density that determines the quantum Brownian motion of a given resonance. Our treatment is valid for low frequencies and provides the leading contribution in the aspect ratio. This yields fundamental limits for the Q-values which are described by simple scaling laws and are relevant for state of the art experimental structures. In this context, for resonant frequencies in the 0.1-1GHz range, while this dissipation mechanism can limit flexural resonators it is found to be negligible for torsional ones. In the case of structureless 3D supports the corresponding environmental spectral densities are Ohmic for flexural resonators and super-Ohmic for torsional ones, while for 2D slab supports they yield 1/f noise. Furthermore analogous results are established for the case of suspended semiconducting single-walled carbon nanotubes. Finally, we provide a general expression for the spectral density that allows to extend our treatment to other geometries and illustrate its use by applying it to a microtoroid. Our analysis is relevant for applications in high precision measurements and for the prospects of probing quantum effects in a macroscopic mechanical degree of freedom.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
