Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userDefects-Assisted Piezoelectric Response in Liquid Exfoliated MoS2 Nanosheets
74
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We report piezoelectric response in liquid phase exfoliated MoS2 nanosheets with desired structure and morphology. The piezoelectric effect in liquid phase exfoliated few layers of MoS2 flakes is interesting as it may allow the scalable fabrication of electronic devices such as self-powered electronics, piezoelectric transformers, antennas and more. The piezo force microscopy (PFM) measurements were used to quantify the amplitude and phase loop, which shows strong piezoelectric coefficient. Herein, the piezoelectric response in few layers of MoS2 is attributed to the defects formed in it during the synthesis procedure. The presence of defects is confirmed by XPS analysis
rate research
Read More
We report a technique for transferring large areas of the CVD-grown, few-layer MoS2 from the original substrate to another arbitrary substrate and onto holey substrates, in order to obtain free-standing structures. The method consists of a polymer- and residue-free, surface-tension-assisted wet transfer, in which we take advantage of the hydrophobic properties of the MoS2. The methods yields better quality transferred layers, with fewer cracks and defects, and less contamination than the widely used PMMA-mediated transfer and allows fabrication of few-layer, fee-standing structures with diameters up to 100 micro-m. We report thermal conductivity measurements by means of contactless Raman thermometry on the so-fabricated samples. The measurements revealed a strong reduction in the in-plane thermal conductivity down to 0.5 W/mK. The results are explained using finite elements method simulations for a polycrystalline film.
The ability to efficiently evolve hydrogen via electrocatalysis at low overpotentials holds tremendous promise for clean energy. Hydrogen evolution reaction (HER) can be easily achieved from water if a voltage above the thermodynamic potential of the HER is applied. Large overpotentials are energetically inefficient but can be lowered with expensive platinum based catalysts. Replacement of Pt with inexpensive, earth abundant electrocatalysts would be significantly beneficial for clean and efficient hydrogen evolution. Towards this end, promising HER characteristics have been reported using 2H (trigonal prismatic) XS2 (where X = Mo or W) nanoparticles with a high concentration of metallic edges as electrocatalysts. The key challenges for HER with XS2 are increasing the number and catalytic activity of active sites. Here we report atomically thin nanosheets of chemically exfoliated WS2 as efficient catalysts for hydrogen evolution with very low overpotentials. Atomic-resolution transmission electron microscopy and spectroscopy analyses indicate that enhanced electrocatalytic activity of WS2 is associated with high concentration of strained metallic 1T (octahedral) phase in the as-exfoliated nanosheets. Density functional theory calculations reveal that the presence of strain in the 1T phase leads to an enhancement of the density of states at the Fermi level and increases the catalytic activity of the WS2 nanosheet. Our results suggest that chemically exfoliated WS2 nanosheets could be interesting catalysts for hydrogen evolution.
We studied the stability and superconductivity of FeSe nanosheets during an in-air device fabrication process. Methods were developed to improve the exfoliation yield and to maintain the superconductivity of FeSe. Raman spectroscopy, atomic force microscopy, optical microscopy and time-of-flight-secondary-ion-mass-spectroscopy measurements show that FeSe nanosheets decayed in air. Precipitation of Se particles and iron oxidation likely occurred during the decay process. Transport measurements revealed that the superconductivity of FeSe disappeared during a conventional electron beam lithography process. Shadow mask evaporation and transfer onto pre-defined electrodes methods were shown to be effective in maintaining the superconductivity after the in-air device fabrication process. These methods developed provide a way of making high quality FeSe nano-devices.
Liquid phase exfoliation is a commonly used method to produce 2D nanosheets from a range of layered crystals. However, such nanosheets display broad size and thickness distributions and correlations between area and thickness, issues that limit nanosheet application potential. To understand the factors controlling the exfoliation process, we have liquid-exfoliated 11 different layered materials, size-selecting each into fractions before using AFM to measure the nanosheet length, width, and thickness distributions for each fraction. The resultant data show a clear power-law scaling of nanosheet area with thickness for each material. We have developed a simple nonequilibrium thermodynamics-based model predicting that the power-law prefactor is proportional to both the ratios of in-plane-tearing/out-of-plane-peeling energies and in-plane/out-of-plane moduli. By comparing the experimental data with the modulus ratio calculated from first-principles, we find close agreement between experiment and theory. This supports our hypothesis that energy equipartition holds between nanosheet tearing and peeling during sonication-assisted exfoliation.
For the first time, the magnetic force microscopy (MFM) is used to characterize the mechanically-exfoliated single- and few-layer MoS2 and graphene nanosheets. By analysis of the phase and amplitude shifts, the magnetic response of MoS2 and graphene nanosheets exhibits the dependence on their layer number. However, the solution-processed single-layer MoS2 nanosheet shows the reverse magnetic signal to the mechanically-exfoliated one, and the graphene oxide nanosheet has not shown any detectable magnetic signal. Importantly, graphene and MoS2 flakes become nonmagnetic when they exceed a certain thickness.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
