Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userRate-dependent adhesion of viscoelastic contacts. Part I: contact area and contact line velocity within model multi-asperity contacts with rubber
52
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
In this work, we investigate dissipative effects involved during the detachment of a smooth spherical glass probe from a viscoelastic silicone substrate patterned with micro-asperities. As a baseline, the pull-off of a single asperity, millimeter-sized contact between a glass lens and a smooth poly(dimethylsiloxane) (PDMS) rubber is first investigated as a function of the imposed detachment velocity. From a measurement of the contact radius a(t) and normal load during unloading, the dependence of the strain energy relase rate G on the velocity of the contact line vc = da/dt is determined under the assumption that viscoelastic dissipation is localized at the edge of the contact. These data are incorporated into Mullers model (V.M. Muller J Adh Sci Tech (1999) 13 999-1016) in order to predict the time-dependence of the contact size. Similar pull-off experiments are carried out with the same PDMS substrate patterned with spherical micro-asperities with a prescribed height distribution. From in situ optical measurements of the micro-contacts, scaling laws are identified for the contact radius a and the contact line velocity vc. On the basis of the observed similarity between macro and microscale contacts, a numerical solution is developed to predict the reduction of the contact radius during unloading.
rate research
Read More
In this paper, we propose a numerical model to describe the adhesive normal contact between a rigid spherical indenter and a viscoelastic rough substrate. The model accounts for dissipative process under the assumption that viscoelastic losses are localized at the (micro)-contact lines. Numerical predictions are then compared with experimental measurements, which show a strong adhesion hysteresis mostly due to viscous energy dissipation occurring during pull-off. This hysteresis is satisfactorily described by the contact model which allows to distinguish the energy loss due to material dissipation from the adhesion hysteresis due to elastic instability. Our analysis shows that the pull-off force required to detach the surfaces is strongly influenced by the detachment rate and the rms roughness amplitude, but it is almost unaffected by the maximum load from which unloading starts. Moreover, the increase in the boundary line separating contact and non-contact regions, observed when moving from smooth to rough contacts, negligibly affects the viscous dissipation. Such increase is much less significant than the reduction in contact area, which therefore is the main parameter governing the strong decrease in the effective surface energy.
We report on normal contact and friction measurements of model multicontact interfaces formed between smooth surfaces and substrates textured with a statistical distribution of spherical micro-asperities. Contacts are either formed between a rigid textured lens and a smooth rubber, or a flat textured rubber and a smooth rigid lens. Measurements of the real area of contact $A$ versus normal load $P$ are performed by imaging the light transmitted at the microcontacts. For both interfaces, $A(P)$ is found to be sub-linear with a power law behavior. Comparison to two multi-asperity contact models, which extend Greenwood-Williamson (J. Greenwood, J. Williamson, textit{Proc. Royal Soc. London Ser. A} textbf{295}, 300 (1966)) model by taking into account the elastic interaction between asperities at different length scales, is performed, and allows their validation for the first time. We find that long range elastic interactions arising from the curvature of the nominal surfaces are the main source of the non-linearity of $A(P)$. At a shorter range, and except for very low pressures, the pressure dependence of both density and area of micro-contacts remains well described by Greenwood-Williamsons model, which neglects any interaction between asperities. In addition, in steady sliding, friction measurements reveal that the mean shear stress at the scale of the asperities is systematically larger than that found for a macroscopic contact between a smooth lens and a rubber. This suggests that frictional stresses measured at macroscopic length scales may not be simply transposed to microscopic multicontact interfaces.
We study experimentally and theoretically the equilibrium adhesive contact between a smooth glass lens and a rough rubber surface textured with spherical microasperities with controlled height and spatial distributions. Measurements of the real contact area $A$ versus load $P$ are performed under compression by imaging the light transmitted at the microcontacts. $A(P)$ is found to be non-linear and to strongly depend on the standard deviation of the asperity height distribution. Experimental results are discussed in the light of a discrete version of Fuller and Tabors (FT) original model (textit{Proceedings of the Royal Society A} textbf{345} (1975) 327), which allows to take into account the elastic coupling arising from both microasperities interactions and curvature of the glass lens. Our experimental data on microcontact size distributions are well captured by our discrete extended model. We show that the elastic coupling arising from the lens curvature has a significant contribution to the $A(P)$ relationship. Our discrete model also clearly shows that the adhesion-induced effect on $A$ remains significant even for vanishingly small pull-off forces. Last, at the local asperity length scale, our measurements show that the pressure dependence of the microcontacts density can be simply described by the original FT model.
This paper addresses the issue of the determination of the frictional stress distribution from the inversion of the measured surface displacement field for sliding interfaces between a glass lens and a rubber (poly(dimethylsiloxane)) substrate. Experimental results show that high lateral strains are achieved at the periphery of the sliding contacts. As a consequence, an accurate inversion of the displacement field requires that finite strains and non linear response of the rubber substrate are taken into account. For that purpose, a Finite Element (FE) inversion procedure is implemented where the measured displacement field is applied as a boundary condition at the upper surface of a meshed body representing the rubber substrate. Normal pressure is also determined by the same way, if non-diverging values are assumed at the contact edge. This procedure is applied to linearly sliding contacts as well as on twisting contacts.
We report on a theoretical and experimental investigation of the normal contact of stretched neo-Hookean substrates with rigid spherical probes. Starting from a published formulation of surface Greens function for incremental displacements on a pre-stretched, neo-Hookean, substrate (L.H. Lee textit{J. Mech. Phys. Sol.} textbf{56} (2008) 2957-2971), a model is derived for both adhesive and non-adhesive contacts. The shape of the elliptical contact area together with the contact load and the contact stiffness are predicted as a function of the in-plane stretch ratios $lambda_x$ and $lambda_y$ of the substrate. The validity of this model is assessed by contact experiments carried out using an uniaxally stretched silicone rubber. for stretch ratio below about 1.25, a good agreement is observed between theory and experiments. Above this threshold, some deviations from the theoretical prediction are induced as a result of the departure of the mechanical response of the silicone rubber from the neo-Hokeean description embedded in the model.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
