Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userTime-Resolved Open-Circuit Conductive Atomic Force Microscopy for Quantitative Analysis of Nanowire Piezoelectricity and Triboelectricity
354
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Piezoelectric nanowires are promising materials for sensing, actuation and energy harvesting, due to their enhanced properties at the nanoscale. However, quantitative characterization of piezoelectricity in nanomaterials is challenging due to practical limitations and the onset of additional electromechanical phenomena, such as the triboelectric and piezotronic effects. Here, we present an open-circuit conductive atomic force microscopy (cAFM) methodology for quantitative extraction of the axial piezoelectric coefficients of nanowires. We show, both theoretically and experimentally, that the standard short-circuit cAFM mode is inadequate for piezoelectric characterization of nanowires, and that such measurements are governed by competing mechanisms. We introduce an alternative open-circuit configuration, and employ time-resolved electromechanical measurements, to extract the piezoelectric coefficients. This method was applied to GaAs, an important semiconductor, with relatively low piezoelectric coefficients. The results obtained for GaAs,~0.4-1 pm/V, are in good agreement with existing knowledge and theory. Our method represents a significant advance in understanding the coexistence of different electromechanical effects, and in quantitative piezoelectric nanoscale characterization. The easy implementation will enable better understanding of electromechanics at the nanoscale.
rate research
Read More
Reliable operation of frequency modulation mode atomic force microscopy (FM-AFM) depends on a clean resonance of an AFM cantilever. It is recognized that the spurious mechanical resonances which originate from various mechanical components in the microscope body are excited by a piezoelectric element that is intended for exciting the AFM cantilever oscillation and these spurious resonance modes cause the serious undesirable signal artifacts in both frequency shift and dissipation signals. We present an experimental setup to excite only the oscillation of the AFM cantilever in a fiber-optic interferometer system using optical excitation force. While the optical excitation force is provided by a separate laser light source with a different wavelength (excitation laser : {lambda} = 1310 nm), the excitation laser light is still guided through the same single-mode optical fiber that guides the laser light (detection laser : {lambda} = 1550 nm) used for the interferometric detection of the cantilever deflection. We present the details of the instrumentation and its performance. This setup allows us to eliminate the problems associated with the spurious mechanical resonances such as the apparent dissipation signal and the inaccuracy in the resonance frequency measurement.
Strong confinement of charges in few electron systems such as in atoms, molecules and quantum dots leads to a spectrum of discrete energy levels that are often shared by several degenerate quantum states. Since the electronic structure is key to understanding their chemical properties, methods that probe these energy levels in situ are important. We show how electrostatic force detection using atomic force microscopy reveals the electronic structure of individual and coupled self-assembled quantum dots. An electron addition spectrum in the Coulomb blockade regime, resulting from a change in cantilever resonance frequency and dissipation during tunneling events, shows one by one electron charging of a dot. The spectra show clear level degeneracies in isolated quantum dots, supported by the first observation of predicted temperature-dependent shifts of Coulomb blockade peaks. Further, by scanning the surface we observe that several quantum dots may reside on what topologically appears to be just one. These images of grouped weakly and strongly coupled dots allow us to estimate their relative coupling strengths.
Domains walls and topological defects in ferroelectric materials have emerged as a powerful new paradigm for functional electronic devices including memory and logic. Similarly, wall interactions and dynamics underpin a broad range of mesoscale phenomena ranging from giant electromechanical responses to memory effects. Exploring the functionalities of individual domain walls, their interactions, and controlled modifications of the domain structures is crucial for applications and fundamental physical studies. However, the dynamic nature of these features severely limits studies of their local physics since application of local biases or pressures in piezoresponse force microscopy induce wall displacement as a primary response. Here, we introduce a fundamentally new approach for the control and modification of domain structures based on automated experimentation whereby real space image-based feedback is used to control the tip bias during ferroelectric switching, allowing for modification routes conditioned on domain states under the tip. This automated experiment approach is demonstrated for the exploration of domain wall dynamics and creation of metastable phases with large electromechanical response.
Ultrasound Atomic Force Microscopy (US-AFM) has been used for subsurface imaging of nanostructures. The contact stiffness variations have been suggested as the origin of the image contrast. Therefore, to analyze the image contrast, the local changes in the contact stiffness due to the presence of subsurface features should be calculated. So far, only static simulations have been conducted to analyze the local changes in the contact stiffness and, consequently, the contrast in US-AFM. Such a static approach does not fully represent the real US-AFM experiment, where an ultrasound wave is launched either into the sample or at the tip, which modulates the contact stiffness. This is a time-dependent nonlinear dynamic problem rather than a static and stationary one. This letter presents dynamic 3D ultrasound analysis of contact stiffness in US-AFM (in contrast to static analysis) to realistically predict the changes in contact stiffness and thus the changes in the subsurface image contrast. The modulation frequency also influences the contact stiffness variations and, thus, the image contrast. The three-dimensional time-dependent ultrasound analysis will greatly aid in the contrast optimization of subsurface nanoimaging with US-AFM.
While offering unprecedented resolution of atomic and electronic structure, Scanning Probe Microscopy techniques have found greater challenges in providing reliable electrostatic characterization at the same scale. In this work, we introduce Electrostatic Discovery Atomic Force Microscopy, a machine learning based method which provides immediate quantitative maps of the electrostatic potential directly from Atomic Force Microscopy images with functionalized tips. We apply this to characterize the electrostatic properties of a variety of molecular systems and compare directly to reference simulations, demonstrating good agreement. This approach opens the door to reliable atomic scale electrostatic maps on any system with minimal computational overhead.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
