No Arabic abstract
Zinc-based nitride CaZn2N2 films grown by molecular beam epitaxy (MBE) with a plasma-assisted active nitrogen-radical source are promising candidates of next-generation semiconductors for light-emitting diodes and solar cells. This nitride compound has previously only been synthesized in a bulk form by ultrahigh-pressure synthesis at 5 GPa. Three key factors have been found to enable heteroepitaxial film growth: (i) precise tuning of the individual flux rates of Ca and Zn, (ii) the use of GaN template layers on sapphire c-plane as substrates, and (iii) the application of MBE with an active N-radical source. Because other attempts at physical vapor deposition and thermal annealing processes have not produced CaZn2N2 films of any phase, this rf-plasma-assisted MBE technique represents a promising way to stabilize CaZn2N2 epitaxial films. The estimated optical band gap is ~1.9 eV, which is consistent with the value obtained from bulk samples. By unintentional carrier doping, n- and p-type electronic conductions are attained with low carrier densities of the order of 1013 /cm3. These features represent clear advantages when compared with Zn-based oxide semiconductors, which usually have much higher carrier densities irrespective of their intentionally undoped state. The carrier mobilities at room temperature are 4.3 cm2/(Vs) for electrons and 0.3 cm2/(Vs) for hole carriers, which indicates that transport properties are limited by grain boundary scattering, mainly because of the low-temperature growth at 250 {deg}C, which realizes a high nitrogen chemical potential.
Pulsed laser deposition, a non-equilibrium thin-film growth technique, was used to stabilize metastable tetragonal iron sulfide (FeS), the bulk state of which is known as a superconductor with a critical temperature of 4 K. Comprehensive experiments revealed four important factors to stabilize tetragonal FeS epitaxial thin films: (i) an optimum growth temperature of 300 {deg}C followed by thermal quenching, (ii) an optimum growth rate of ~7 nm/min, (iii) use of a high-purity bulk target, and (iv) use of a single-crystal substrate with small in-plane lattice mismatch (CaF2). Electrical resistivity measurements indicated that none of all the films exhibited superconductivity. Although an electric double-layer transistor structure was fabricated using the tetragonal FeS epitaxial film as a channel layer to achieve high-density carrier doping, no phase transition was observed. Possible reasons for the lack of superconductivity include lattice strain, off-stoichiometry of the film, electrochemical etching by the ionic liquid under gate bias, and surface degradation during device fabrication.
Strain engineering vanadium dioxide thin films is one way to alter this materials characteristic first order transition from semiconductor to metal. In this study we extend the exploitable strain regime by utilizing the very large lattice mismatch of 8.78 % occurring in the VO$_2$/RuO$_2$ system along the c axis of the rutile structure. We have grown VO$_2$ thin films on single domain RuO$_2$ islands of two distinct surface orientations by atomic oxygen-supported reactive MBE. These films were examined by spatially resolved photoelectron and x-ray absorption spectroscopy, confirming the correct stoichiometry. Low energy electron diffraction then reveals the VO$_2$ films to grow indeed fully strained on RuO$_2$(110), exhibiting a previously unreported ($2times2$) reconstruction. On TiO$_2$(110) substrates, we reproduce this reconstruction and attribute it to an oxygen-rich termination caused by the high oxygen chemical potential. On RuO$_2$(100) on the other hand, the films grow fully relaxed. Hence, the presented growth method allows for simultaneous access to a remarkable strain window ranging from bulk-like structures to massively strained regions.
Following the recent discovery of large magnetoresistance at room temperature in polyfluorence sandwich devices, we have performed a comprehensive magnetoresistance study on a set of organic semiconductor sandwich devices made from different pi-conjugated polymers and small molecules. The measurements were performed at different temperatures, ranging from 10K to 300K, and at magnetic fields, $B < 100mT$. We observed large negative or positive magnetoresistance (up to 10% at 300K and 10mT) depending on material and device operating conditions. We compare the results obtained in devices made from different materials with the goal of providing a comprehensive picture of the experimental data. We discuss our results in the framework of known magnetoresistance mechanisms and find that none of the existing models can explain our results.
We present results on growth of large area epitaxial ReS2 thin film both on c plane sapphire substrate and MoS2 template by pulsed laser deposition (PLD). Films tend to grow with (0001) ReS2 perpendicular to (0001) Al2O3 and (0001) ReS2 perpendicular to (0001) MoS2 parallel to (0001) Al2O3 at deposition temperature below 300 deg C. Films are polycrystalline grown at temperature above 300 deg C. The smoothness and quality of the films are significantly improved when grown on MoS2 template compared to sapphire substrate. The results show that PLD is suitable to grow ReS2 epitaxial thin film over large area for practical device application.
Epitaxial Mn-doped BiFeO3 (MBFO) thin films were grown on GaAs (001) substrate with SrTiO3 (STO) buffer layer by pulsed laser deposition. X-ray diffraction results demonstrate that the films show pure (00l) orientation, and MBFO(100)//STO(100), whereas STO (100)//GaAs (110). Piezoresponse force microscopy images and polarization versus electric field loops indicate that the MBFO films grown on GaAs have an effective ferroelectric switching. The MBFO films exhibit good ferroelectric behavior (2Pr ~ 92 {mu}C/cm2 and 2EC ~ 372 kV/cm). Ferromagnetic property with saturated magnetization of 6.5 emu/cm3 and coercive field of about 123 Oe is also found in the heterostructure at room temperature.