Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userTowards Ultrafast Gyroscopes Employing Real-time Intensity and Spectral Domain Measurements of Ultrashort Pulses
72
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Active ring laser gyroscopes (RLG) operating on the principle of the optical Sagnac effect are preferred instruments for a range of applications, such as inertial guidance systems, seismology, and geodesy, that require both high bias stability and high angular velocity resolutions. Operating at such accuracy levels demands special precautions like dithering or multi-mode operation to eliminate frequency lock-in or similar effects introduced due to synchronisation of counter-propagating channels. Recently proposed bidirectional ultrafast fibre lasers can circumvent the limitations of continuous wave RLGs. However, their performance is limited due to the nature of the highly-averaged interrogation of the Sagnac effect. In general, the performance of current optical gyroscopes relies on the available measurement methods used for extracting the signal. Here, by changing the paradigm of traditional measurement and applying spatio-temporal intensity processing, we demonstrate that the bidirectional ultrafast laser can be transformed to an ultrafast gyroscope with acquisition rates of the order of the laser repetition rate, making them at least two orders of magnitude faster than commercially deploy
rate research
Read More
The spectrum of laser-plasma generated X-rays is very important, it characterizes electron dynamics in plasma and is basic for applications. However, the accuracies and efficiencies of existing methods to diagnose the spectrum of laser-plasma based X-ray pulse are not very high, especially in the range of several hundred keV. In this study, a new method based on electron tracks detection to measure the spectrum of laser-plasma produced X-ray pulses is proposed and demonstrated. Laser-plasma generated X-rays are scattered in a multi-pixel silicon tracker. Energies and scattering directions of Compton electrons can be extracted from the response of the detector, and then the spectrum of X-rays can be reconstructed. Simulations indicate that the energy resolution of this method is approximately 20% for X-rays from 200 to 550 keV for a silicon-on-insulator pixel detector with 12 $rm mu$m pixel pitch and 500 $rm mu$m depletion region thickness. The results of a proof-of-principle experiment based on a Timepix3 detector are also shown.
Superconducting transition-edge sensors (TES) are extremely sensitive microcalorimeters used as photon detectors with unparalleled energy resolution. They have found application from measuring astronomical spectra through to determining the quantum property of photon-number, $hat{n} {=} hat{a}^{dag} hat{a}$, for energies from 0.6-2.33eV. However, achieving optimal energy resolution requires considerable data acquisition -- on the order of 1GB/min -- followed by post-processing, which does not allow access to energy information in real time. Here we use a custom hardware processor to process TES pulses while new detections are still being registered, allowing photon-number to be measured in real time as well as reducing data requirements by orders-of-magnitude. We resolve photon number up to n=16 -- achieving up to parts-per-billion discrimination for low photon numbers on the fly -- providing transformational capacity for applications of TES detectors from astronomy through to quantum technology.
Frequency to time mapping is a powerful technique for observing ultrafast phenomena and non-repetitive events in optics. However, many optical sources operate in wavelength regions, or at power levels, that are not compatible with standard frequency to time mapping implementations. The recently developed free-space angular chirp enhanced delay (FACED) removes many of these limitations, and offers a linear frequency to time mapping in any wavelength region where high-reflectivity mirrors and diffractive optics are available. In this work, we present a detailed formulation of the optical transfer function of a FACED device. Experimentally, we verify the properties of this transfer function, and then present simple guidelines to guarantee the correct operation of a FACED frequency to time measurement. We also experimentally demonstrate the real-time spectral analysis of femtosecond and picosecond pulses using this system.
We present the experimental test of a method for controlling the absolute length of the diagonals of square ring laser gyroscopes. The purpose is to actively stabilize the ring cavity geometry and to enhance the rotation sensor stability in order to reach the requirements for the detection of the relativistic Lense-Thirring effect with a ground-based array of optical gyroscopes. The test apparatus consists of two optical cavities 1.32 m in length, reproducing the features of the ring cavity diagonal resonators of large frame He-Ne ring laser gyroscopes. The proposed measurement technique is based on the use of a single diode laser, injection locked to a frequency stabilized He-Ne/Iodine frequency standard, and a single electro-optic modulator. The laser is modulated with a combination of three frequencies allowing to lock the two cavities to the same resonance frequency and, at the same time, to determine the cavity Free Spectral Range (FSR). We obtain a stable lock of the two cavities to the same optical frequency reference, providing a length stabilization at the level of 1 part in $10^{11}$, and the determination of the two FSRs with a relative precision of 0.2 ppm. This is equivalent to an error of 500 nm on the absolute length difference between the two cavities.
Lead-magnesium niobate lead-titanate (PMN-PT) has been proven as an excellent material for sensing and actuating applications. The fabrication of advanced ultra-small PMN-PT-based devices relies on the availability of sophisticated procedures for the micro-machining of PMN-PT thin films or bulk substrates. Approaches reported up to date include chemical etching, excimer laser ablation and ion milling. To ensure an excellent device performance, a key mandatory feature for a micro-machining process is to preserve as far as possible the crystalline quality of the substrates; in other words, the fabrication method must induce a low density of cracks and other kind of defects. In this work, we demonstrate a relatively fast procedure for the fabrication of high-quality PMN-PT micro-machined actuators employing green femtosecond laser pulses. The fabricated devices feature absence of extended cracks and well defined edges with relatively low roughness, which is advantageous for the further integration of nanomaterials onto the piezoelectric actuators.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
