Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userUnderstanding contact gating in Schottky barrier transistors from 2D channels
58
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
In this article, a novel two-path model is proposed to quantitatively explain sub-threshold characteristics of back-gated Schottky barrier FETs (SB-FETs) from 2D channel materials. The model integrates the conventional model for SB-FETs with the phenomenon of contact gating - an effect that significantly affects the carrier injection from the source electrode in back-gated field effect transistors. The two-path model is validated by a careful comparison with experimental characteristics obtained from a large number of back-gated WSe2 devices with various channel thicknesses. Our findings are believed to be of critical importance for the quantitative analysis of many three-terminal devices with ultrathin body channels.
rate research
Read More
Schottky barrier field-effect transistors (SBFETs) based on few and mono layer phosphorene are simulated by the non-equilibrium Greens function formalism. It is shown that scaling down the gate oxide thickness results in pronounced ambipolar I-V characteristics and significant increase of the minimal leakage current. The problem of leakage is especially severe when the gate insulator is thin and the number of layer is large, but can be effectively suppressed by reducing phosphorene to mono or bilayer. Different from two-dimensional graphene and layered dichalcogenide materials, both the ON-current of the phosphorene SBFETs and the metal-semiconductor contact resistance between metal and phosphorene strongly depend on the transport crystalline direction.
Metal contacts have been identified to be a key technological bottleneck for the realization of viable graphene electronics. Recently, it was observed that for structures that possess both a top and a bottom gate, the electron-hole conductance asymmetry can be modulated by the bottom gate. In this letter, we explain this observation by postulating the presence of an effective thin interfacial dielectric layer between the metal contact and the underlying graphene. Electrical results from quantum transport calculations accounting for this modified electrostatics corroborate well with the experimentally measured contact resistances. Our study indicates that the engineering of metal- graphene interface is a crucial step towards reducing the contact resistance for high performance graphene transistors.
The observed performances of carbon nanotube field effect transistors are examined using first-principles quantum transport calculations. We focus on the nature and role of the electrical contact of Au and Pd electrodes to open-ended semiconducting nanotubes, allowing the chemical contact at the surface to fully develop through large-scale relaxation of the contacting atomic configuration. We present the first direct numerical evidence of Pd contacts exhibiting perfect transparency for hole injection as opposed to that of Au contacts. Their respective Schottky barrier heights, on the other hand, turn out to be fairly similar for realistic contact models. These findings are in general agreement with experimental data reported to date, and show that a Schottky contact is not merely a passive ohmic contact but actively influences the device I-V behavior.
The paradigm of graphene transistors is based on the gate modulation of the channel carrier density by means of a local channel gate. This standard architecture is subject to the scaling limit of the channel length and further restrictions due to access and contact resistances impeding the device performance. We propose a novel design, overcoming these issues by implementing additional local gates underneath the contact region which allow a full control of the Klein barrier taking place at the contact edge. In particular, our work demonstrates the GHz operation of transistors driven by independent contact gates. We benchmark the standard channel and novel contact gating and report for the later dynamical transconductance levels at the state of the art. Our finding may find applications in electronics and optoelectronics whenever there is need to control independently the Fermi level and the electrostatic potential of electronic sources or to get rid of cumbersome local channel gates.
We discuss the high-bias electrical characteristics of back-gated field-effect transistors with CVD-synthesized bilayer MoS2 channel and Ti Schottky contacts. We find that oxidized Ti contacts on MoS2 form rectifying junctions with ~0.3 to 0.5 eV Schottky barrier height. To explain the rectifying output characteristics of the transistors, we propose a model based on two slightly asymmetric back-to-back Schottky barriers, where the highest current arises from image force barrier lowering at the electrically forced junction, while the reverse current is due to Schottky-barrier limited injection at the grounded junction. The device achieves a photo responsivity greater than 2.5 AW-1 under 5 mWcm-2 white-LED light. By comparing two- and four-probe measurements, we demonstrate that the hysteresis and persistent photoconductivity exhibited by the transistor are peculiarities of the MoS2 channel rather than effects of the Ti/MoS2 interface.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
