Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userQuantitative Observation of Magnetic Flux Distribution in New Magnetic Films for Future High Density Recording Media
277
0
0.0
(
0
)
Added by
Aurelien Masseboeuf
Publication date
2009
fields
Physics
and research's language is
English
Authors
Aurelien Masseboeuf
Ask ChatGPT about the research
No Arabic abstract
Off-axis electron holography was used to observe and quantify the magnetic microstructure of a perpendicular magnetic anisotropic (PMA) recording media. Thin foils of PMA materials exhibit an interesting up and down domain configuration. These domains are found to be very stable and were observed at the same time with their stray field, closing magnetic flux in the vacuum. The magnetic moment can thus be determined locally in a volume as small as few tens of cubic nanometers.
rate research
Read More
Manipulation of the magnetization by external energies other than magnetic field, such as spin-polarized current1-4, electric voltage5,6 and circularly polarized light7-11 gives a paradigm shift in magnetic nanodevices. Magnetization control of ferromagnetic materials only by circularly polarized light has received increasing attention both as a fundamental probe of the interactions of light and magnetism but also for future high-density magnetic recording technologies. Here we show that for granular FePt films, designed for ultrahigh-density recording, the optical magnetic switching by circularly polarized light is an accumulative effect from multiple optical pulses. We further show that deterministic switching of high anisotropy materials by the combination of circularly polarized light and modest external magnetic fields, thus revealing a pathway towards technological implementation.
The development of high-density magnetic recording media is limited by the superparamagnetism in very small ferromagnetic crystals. Hard magnetic materials with strong perpendicular anisotropy offer stability and high recording density. To overcome the difficulty of writing media with a large coercivity, heat assisted magnetic recording (HAMR) has been developed, rapidly heating the media to the Curie temperature Tc before writing, followed by rapid cooling. Requirements are a suitable Tc, coupled with anisotropic thermal conductivity and hard magnetic properties. Here we introduce Rh2CoSb as a new hard magnet with potential for thin film magnetic recording. A magnetocrystalline anisotropy of 3.6 MJm-3 is combined with a saturation magnetization of {mu}0Ms = 0.52 T at 2 K (2.2 MJm-3 and 0.44 T at room-temperature). The magnetic hardness parameter of 3.7 at room temperature is the highest observed for any rare-earth free hard magnet. The anisotropy is related to an unquenched orbital moment of 0.42 {mu}B on Co, which is hybridized with neighbouring Rh atoms with a large spin-orbit interaction. Moreover, the pronounced temperature-dependence of the anisotropy that follows from its Tc of 450 K, together with a high thermal conductivity of 20 Wm-1K-1, makes Rh2CoSb a candidate for development for heat assisted writing with a recording density in excess of 10 Tb/in2.
A micromagnetic study of epitaxial micron-sized iron dots is reported through the analysis of Fresnel contrast in Lorentz Microscopy. Their use is reviewed and developed through analysis of various magnetic structures in such dots. Simple Landau configuration is used to investigate various aspects of asymmetric Bloch domain walls. The experimental width of such a complex wall is first derived and its value is discussed with the help of micromagnetic simulations. Combination of these two approaches enables us to define what is really extracted when estimating asymmetric wall width in Lorentz Microscopy. Moreover, quantitative data on the magnetization inside the dot is retrieved using phase retrieval as well as new informations on the degrees of freedom of such walls. Finally, it is shown how the existence and the propagation of a surface vortex can be characterized and monitored. This demonstrates the ability to reach a magnetic sensitivity a priori hidden in Fresnel contrast, based on an original image treatment and backed-up by the evaluation of contrasts obtained from micromagnetic simulations.
Bit Patterned Media (BPM) for magnetic recording provide a route to densities $>1 Tb/in^2$ and circumvents many of the challenges associated with conventional granular media technology. Instead of recording a bit on an ensemble of random grains, BPM uses an array of lithographically defined isolated magnetic islands, each of which stores one bit. Fabrication of BPM is viewed as the greatest challenge for its commercialization. In this article we describe a BPM fabrication method which combines e-beam lithography, directed self-assembly of block copolymers, self-aligned double patterning, nanoimprint lithography, and ion milling to generate BPM based on CoCrPt alloys. This combination of fabrication technologies achieves feature sizes of $<10 nm$, significantly smaller than what conventional semiconductor nanofabrication methods can achieve. In contrast to earlier work which used hexagonal close-packed arrays of round islands, our latest approach creates BPM with rectangular bitcells, which are advantageous for integration with existing hard disk drive technology. The advantages of rectangular bits are analyzed from a theoretical and modeling point of view, and system integration requirements such as servo patterns, implementation of write synchronization, and providing for a stable head-disk interface are addressed in the context of experimental results. Optimization of magnetic alloy materials for thermal stability, writeability, and switching field distribution is discussed, and a new method for growing BPM islands on a patterned template is presented. New recording results at $1.6 Td/in^2$ (teradot/inch${}^2$, roughly equivalent to $1.3 Tb/in^2$) demonstrate a raw error rate $<10^{-2}$, which is consistent with the recording system requirements of modern hard drives. Extendibility of BPM to higher densities, and its eventual combination with energy assisted recording are explored.
A low-cost and simple setup for measuring the high-frequency hysteresis loops of magnetic samples is described. An AMF in the range 6-100 kHz with amplitude up to 80 mT is produced by a Litz wire coil. The latter is air-cooled using a forced-air approach so no water flow is required to run the setup. High-frequency hysteresis loops are measured using a system of pick-up coils and numerical integration of signals. Reproducible measurements are obtained in the frequency range of 6-56 kHz. Measurement examples on ferrite cylinders and on iron oxide nanoparticle ferrofluids are shown. Comparison with other measurement methods of the hysteresis loop area (complex susceptibility, quasi-static hysteresis loops and calorific measurements) is provided and shows the coherency of the results obtained with this setup. This setup is well adapted to the magnetic characterization of colloidal solutions of MNPs for magnetic hyperthermia applications.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
