Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userFirst-principles calculations and bias-dependent STM measurements at the alpha-Sn/Ge(111) surface: a clear indication for the 1U2D configuration
325
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The nature of the alpha-Sn/Ge(111) surface is still a matter of debate. In particular, two possible configurations have been proposed for the 3x3 ground state of this surface: one with two Sn adatoms in a lower position with respect to the third one (1U2D) and the other with opposite configuration (2U1D). By means of first-principles quasiparticle calculations we could simulate STM images as a function of bias voltage and compare them with STM experimental results at 78K, obtaining an unambiguous indication that the stable configuration for the alpha-Sn/Ge(111) surface is the 1U2D. The possible inequivalence of the two down Sn adatoms is also discussed.
rate research
Read More
A nanorod structure has been observed on the Ho/Ge(111) surface using scanning tunneling microscopy (STM). The rods do not require patterning of the surface or defects such as step edges in order to grow as is the case for nanorods on Si(111). At low holmium coverage the nanorods exist as isolated nanostructures while at high coverage they form a periodic 5x1 structure. We propose a structural model for the 5x1 unit cell and show using an ab initio calculation that the STM profile of our model structure compares favorably to that obtained experimentally for both filled and empty states sampling. The calculated local density of states shows that the nanorod is metallic in character.
In this Letter, we present the first non-contact atomic force microscopy (nc-AFM) of a silicene on silver (Ag) surface, obtained by combining non-contact atomic force microscopy (nc-AFM) and scanning tunneling microscopy (STM). STM images over large areas of silicene grown on Ag(111) surface show both (sqrt13xsqrt13)R13.9{deg} and (4x4) superstructures. For the widely observed (4x4) structure, the nc-AFM topography shows an atomic-scale contrast inversion as the tip-surface distance is decreased. At the shortest tip-surface distance, the nc-AFM topography is very similar to the STM one. The observed structure in the nc-AFM topography is compatible with only one out of two silicon atoms being visible. This indicates unambiguously a strong buckling of the silicene honeycomb layer.
We report an investigation on the properties of 0.33 ML of Sn on Ge(111) at temperatures down to 5 K. Low-energy electron diffraction and scanning tunneling microscopy show that the (3x3) phase formed at 200 K, reverts to a new (root-3xroot-3)R30 phase below 30 K. The vertical distortion characteristic of the (3x3) phase is lost across the phase transition. Angle-resolved photoemission experiments show that concomitantly with the structural phase transition, a metal-insulator phase transition takes place. In agreement with theoretical predictions, the (root-3xroot-3)R30 ground state is interpreted as the experimental realization of a Mott insulator for a narrow half-filled band in a two-dimensional triangular lattice.
Core-level X-ray Photoelectron Spectroscopy (XPS) is often used to study the surfaces of heterogeneous copper-based catalysts, but the interpretation of measured spectra, in particular the assignment of peaks to adsorbed species, can be extremely challenging. In this study we demonstrate that first principles calculations using the delta Self Consistent Field (delta-SCF) method can be used to guide the analysis of experimental core-level spectra of complex surfaces relevant to heterogeneous catalysis. Specifically, we calculate core-level binding energy shifts for a series of adsorbates on Cu(111) and show that the resulting C1s and O1s binding energy shifts for adsorbed CO, CO2, C2H4, HCOO, CH3O, H2O, OH and a surface oxide on Cu(111) are in good overall agreement with the experimental literature. In the few cases where the agreement is less good, the theoretical results may indicate the need to re-examine experimental peak assignments.
We present a systematic study of the atomic and electronic structure of the Si(111)-(5x2)-Au reconstruction using first-principles electronic structure calculations based on the density functional theory. We analyze the structural models proposed by Marks and Plass [Phys. Rev. Lett.75, 2172 (1995)], those proposed recently by Erwin [Phys. Rev. Lett.91, 206101 (2003)], and a completely new structure that was found during our structural optimizations. We study in detail the energetics and the structural and electronic properties of the different models. For the two most stable models, we also calculate the change in the surface energy as a function of the content of silicon adatoms for a realistic range of concentrations. Our new model is the energetically most favorable in the range of low adatom concentrations, while Erwins 5x2 model becomes favorable for larger adatom concentrations. The crossing between the surface energies of both structures is found close to 1/2 adatoms per 5x2 unit cell, i.e. near the maximum adatom coverage observed in the experiments. Both models, the new structure and Erwins 5x2 model, seem to provide a good description of many of the available experimental data, particularly of the angle-resolved photoemission measurements.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
