اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدFlow profiles near receding three--phase contact lines: Influence of surfactants
104
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The dynamics of wetting and dewetting is largely determined by the velocity field near the contact lines. For water drops it has been observed that adding surfactant decreases the dynamic receding contact angle even at a concentration much lower than the critical micelle concentration (CMC). To better understand why surfactants have such a drastic effect on drop dynamics, we constructed a dedicated a setup on an inverted microscope, in which an aqueous drop is held stationary while the transparent substrate is moved horizontally. Using astigmatism particle tracking velocimetry, we track the 3D displacement of the tracer particles in the flow. We study how surfactants alter the flow dynamics near the receding contact line of a moving drop for capillary numbers in the order of $10^{-6}$. Even for surfactant concentrations $c$ far below the critical micelle concentration ($c ll$ CMC) Marangoni stresses change the flow drastically. We discuss our results first in a 2D model that considers advective and diffusive surfactant transport and deduce estimates of the magnitude and scaling of the Marangoni stress from this. Modeling and experiment agree that a tiny gradient in surface tension of a few $mu N , m^{-1}$ is enough to alter the flow profile significantly. The variation of the Marangoni stress with the distance from the contact line suggests that the 2D advection-diffusion model has to be extended to a full 3D model. The effect is ubiquitous, since surfactant is present in many technical and natural dewetting processes either deliberately or as contamination.
قيم البحث
اقرأ أيضاً
When a solid plate is withdrawn from a liquid bath, a receding contact line is formed where solid, liquid, and gas meet. Above a critical speed $U_{cr}$, a stationary contact line can no longer exist and the solid will eventually be covered completel
y by a liquid film. Here we show that the bifurcation diagram of this coating transition changes qualitatively, from discontinuous to continuous, when decreasing the inclination angle of the plate. We show that this effect is governed by the presence of capillary waves, illustrating that the large scale flow strongly effects the maximum speed of dewetting.
We investigate the internal flow pattern of an evaporating droplet using tomographic particle image velocimetry (PIV) when the contact line non-uniformly recedes. We observe a three-dimensional azimuthal vortex pair while the contact line non-uniform
ly recedes and the symmetry-breaking flow field is maintained during the evaporation. Based on the experimental results, we show that the vorticity magnitude of the internal flow is related to the relative contact line motion. Furthermore, to explain how the azimuthal vortex pair flow is created, we develop a theoretical model by taking into account the relation between the contact line motion and evaporating flux. Finally, we show that the theoretical model has a good agreement with experimental results.
We analyze both theoretically and experimentally the breakup of a pendant water droplet loaded with Sodium Dodecyl Sulfate (SDS). The free surface minimum radius measured in the experiments is compared with that obtained from a numerical solution of
the full Navier-Stokes equations for different values of the shear and dilatational surface viscosities. This comparison shows the small but measurable effect of the surface viscous stresses on the system dynamics for sufficiently small spatiotemporal distances from the breakup point, and allows to establish upper bounds for the values of the shear and dilatational viscosities. We study numerically the distribution of Marangoni and viscous stresses over the free surface as a function of the time to the pinching, and describe how surface viscous stresses grow in the pinching region as the free surface approaches its breakup. When Marangoni and surface viscosity stresses are taken into account, the surfactant is not swept away from the thread neck in the time interval analyzed. Surface viscous stresses eventually balance the driving capillary pressure in that region for small enough values of the time to pinching. Based on this result, we propose a scaling law to account for the effect of the surface viscosities on the last stage of the temporal evolution of the neck radius.
Slender-body approximations have been successfully used to explain many phenomena in low-Reynolds number fluid mechanics. These approximations typically use a line of singularity solutions to represent the flow. These singularities can be difficult t
o implement numerically because they diverge at their origin. Hence people have regularized these singularities to overcome this issue. This regularization blurs the force over a small blob therefore removing the divergent behaviour. However it is unclear how best to regularize the singularities to minimize errors. In this paper we investigate if a line of regularized Stokeslets can describe the flow around a slender body. This is achieved by comparing the asymptotic behaviour of the flow from the line of regularized Stokeslets with the results from slender-body theory. We find that the flow far from the body can be captured if the regularization parameter is proportional to the radius of the slender body. This is consistent with what is assumed in numerical simulations and provides a choice for the proportionality constant. However more stringent requirements must be placed on the regularization blob to capture the near field flow outside a slender body. This inability to replicate the local behaviour indicates that many regularizations cannot satisfy the non-slip boundary conditions on the bodies surface to leading order, with one of the most commonly used regularizations showing an angular dependency of velocity along any cross section. This problem can be overcome with compactly supported blobs { and we construct one such example blob which could be effectively used to simulate the flow around a slender body
In this paper we present experimental and numerical studies of the electrohydrodynamic stretching of a sub-millimetre-sized salt water drop, immersed in oil with added non-ionic surfactant, and subjected to a suddenly applied electric field of magnit
ude approaching 1 kV/mm. By varying the drop size, electric field strength and surfactant concentration we cover the whole range of electric capillary numbers ($Ca_E$) from 0 up to the limit of drop disintegration. The results are compared with the analytical result by Taylor (1964) which predicts the asymptotic deformation as a function of $Ca_E$. We find that the addition of surfactant damps the transient oscillations and that the drops may be stretched slightly beyond the stability limit found by Taylor. We proceed to study the damping of the oscillations, and show that increasing the surfactant concentration has a dual effect of first increasing the damping at low concentrations, and then increasing the asymptotic deformation at higher concentrations. We explain this by comparing the Marangoni forces and the interfacial tension as the drops deform. Finally, we have observed in the experiments a significant hysteresis effect when drops in oil with large concentration of surfactant are subjected to repeated deformations with increasing electric field strengths. This effect is not attributable to the flow nor the interfacial surfactant transport.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
