اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThe Conundrum of Strongly Coupled Supercurrent Flow in Both Under- and Over-doped Bi-2212 Round Wires
76
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Understanding what makes Bi$_2$Sr$_2$Ca$_1$Cu$_2$O$_x$ (Bi-2212) the only high critical current density ($J_c$), high temperature superconductor (HTS) capable of being made as a round wire (RW) is important intellectually because high $J_c$ RW Bi-2212 breaks the paradigm that forces biaxially textured REBCO and uniaxially textured (Bi,Pb)$_2$Sr$_2$Ca$_2$Cu$_3$O$_x$ (Bi-2223) into tape geometries that reproduce the strong anisotropy of the native crystal structure and force expensive fabrication routes to ensure the best possible texture with minimum density of high angle grain boundaries. The biaxial growth texture of Bi-2212 developed during a partial melt heat treatment should favor high $J_c$, even though its $sim$15$^{circ}$ full width at half maximum (FWHM) grain-to-grain misorientation is well beyond the commonly accepted strong-coupling range. Its ability to be strongly overdoped should be valuable too, since underdoped cuprate grain boundaries are widely believed to be weakly linked. Accordingly, we here study property changes after oxygen underdoping the optimized, overdoped wire. While $J_c$ and vortex pinning diminish significantly in underdoped wires, we were not able to develop the prominent weak-link signature (a hysteretic $J_c$(H) characteristic) evident in even the very best Bi-2223 tapes with a $sim$ 15$^{circ}$ FWHM uniaxial texture. We attribute the high $J_c$ and lack of weak link signature in our Bi-2212 round wires to the high-aspect ratio, large-grain, basal-plane-faced grain morphology produced by partial-melt processing of Bi-2212 which enables $c$-axis Brick-Wall current flow when $ab$-plane transport is blocked. We conclude that the presently optimized biaxial texture of Bi-2212 intrinsically constitutes a strongly coupled current path, regardless of its oxygen doping state.
قيم البحث
اقرأ أيضاً
Bi-2212 round wire is made by the powder-in-tube technique. An unavoidable property of powder-in-tube conductors is that there is about 30% void space in the as-drawn wire. We have recently shown that the gas present in the as-drawn Bi-2212 wire aggl
omerates into large bubbles and that they are presently the most deleterious current limiting mechanism. By densifying short 2212 wires before reaction through cold isostatic pressing (CIPping), the void space was almost removed and the gas bubble density was reduced significantly, resulting in a doubled engineering critical current density (JE) of 810 A/mm2 at 5 T, 4.2 K. Here we report on densifying Bi-2212 wire by swaging, which increased JE (4.2 K, 5 T) from 486 A/mm2 for as-drawn wire to 808 A/mm2 for swaged wire. This result further confirms that enhancing the filament packing density is of great importance for making major JE improvement in this round-wire magnet conductor.
Recently the interest about Bi-2212 round wire superconductor for high magnetic field use has been enhancing despite the fact that an increase of the critical current is still needed to boost its successful use in such applications. Recent studies ha
ve demonstrated that the main obstacle to current flow, especially in long wires, is the residual porosity inside these Powder-In-Tube processed conductors which develops in bubbles-agglomeration when the Bi-2212 melts. Through this work we tried to overcome this issue acting on the wire densification by changing the deformation process. Here we show the effects of groove-rolling versus drawing process on the critical current density JC and on the microstructure. In particular, groove-rolled multifilamentary wires show a JC increased by a factor of about 3 with respect to drawn wires prepared with the same Bi-2212 powder and architecture. We think that this approach in the deformation process is able to produce the required improvements both because the superconducting properties are enhanced and because it makes the fabrication process faster and cheaper.
We report measurements of AC susceptibility and hence the in-plane London penetration depth on the same samples of Bi:2212 and Bi(Y):2212 for many values of the planar hole concentration/CuO2 unit (p). These support the scenario in which the pseudoga
p weakens the superconducting response only for p less than approximately 0.19.
Significant insights for critical current density (Jc) improvement in Bi-2212 super- conductor wires can be obtained by an accurate analysis of the structural and mi- crostructural properties evolving during the so-called partial-melt process, a heat
treatment needed to improve grain connectivity and therefore gain high Jc. Here, we report an in-situ analysis by means of synchrotron X-ray and neutron diffraction performed, for the first time, during the heat treatment carried out with the very same temperature profile and reacting oxygen atmosphere in which the Bi-2212 wires are usually treated for practical applications. The obtained results show the thermal evolution of the Bi-2212 structure, focusing in particular on texturing and secondary phases formation. The role of the oxygen is discussed as well. Hence, the present investigation marks a significant advance for the comprehension of the phenomena involved in the wire fabrication process and provides useful insights for the process optimization as well.
We present results of Raman scattering experiments in differently doped Bi-2212 single crystals. Below Tc the spectra show pair-breaking features in the whole doping range. The low frequency power laws confirm the existence of a $d_{x^2-y^2}$-wave or
der parameter. In the normal state between Tc and T* = 200K we find evidence for a pseudogap in B2g symmetry. Upon doping its effect on the spectra decreases while its energy scale appears to be unchanged.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
