اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCo/Ni multilayers for spintronics: high spin-polarization and tunable magnetic anisotropy
97
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this paper we analyze in details the electronic properties of (Co/Ni) multilayers, a model system for spintronics devices. We use magneto-optical Kerr (MOKE), spin-polarized photoemission spectroscopy (SRPES), x-ray magnetic circular dichroism (XMCD) and anomalous surface diffraction experiments to investigate the electronic properties and perpendicular magnetic anisotropy (PMA) in [Co(x)/Ni(y)] single-crystalline stacks grown by molecular beam epitaxy.
قيم البحث
اقرأ أيضاً
[Co/Ni] multilayers with perpendicular magnetic anisotropy (PMA) have been researched and applied in various spintronic applications. Typically the seed layer material is studied to provide the desired face-centered cubic (textit{fcc}) texture to the
[Co/Ni] to obtain PMA. The integration of [Co/Ni] in back-end-of-line (BEOL) processes also requires the PMA to survive post-annealing. In this paper, the impact of NiCr, Pt, Ru, and Ta seed layers on the structural and magnetic properties of [Co(0.3 nm)/Ni(0.6 nm)] multilayers is investigated before and after annealing. The multilayers were deposited textit{in-situ} on different seeds via physical vapor deposition at room temperature. The as-deposited [Co/Ni] films show the required textit{fcc}(111) texture on all seeds, but PMA is only observed on Pt and Ru. In-plane magnetic anisotropy (IMA) is obtained on NiCr and Ta seeds, which is attributed to strain-induced PMA loss. PMA is maintained on all seeds after post-annealing up to 400$^{circ}$C. The largest effective perpendicular anisotropy energy ($K_U^{mathrm{eff}}approx 2times10^5$J/m$^3$) after annealing is achieved on NiCr seed. The evolution of PMA upon annealing cannot be explained by further crystallization during annealing or strain-induced PMA, nor can the observed magnetization loss and the increased damping after annealing. Here we identify the diffusion of the non-magnetic materials from the seed into [Co/Ni] as the major driver of the changes in the magnetic properties. By selecting the seed and post-annealing temperature, the [Co/Ni] can be tuned in a broad range for both PMA and damping.
Using broadband ferromagnetic resonance, we measure the damping parameter of [Co(5 r{A})/Pt(3 r{A})]${times 6}$ multilayers whose growth was optimized to maximize the perpendicular anisotropy. Structural characterizations indicate abrupt interfaces e
ssentially free of intermixing despite the miscible character of Co and Pt. Gilbert damping parameters as low as 0.021 can be obtained despite a magneto-crystalline anisotropy as large as $10^6~textrm{J/m}^3$. The inhomogeneous broadening accounts for part of the ferromagnetic resonance linewidth, indicating some structural disorder leading to a equivalent 20 mT of inhomogenity of the effective field. The unexpectedly relatively low damping factor indicates that the presence of the Pt heavy metal within the multilayer may not be detrimental to the damping provided that intermixing is avoided at the Co/Pt interfaces.
We have studied the magnetic properties of multilayers composed of ferromagnetic metal Co and heavy metals with strong spin orbit coupling (Pt and Ir). Multilayers with symmetric (ABA stacking) and asymmetric (ABC stacking) structures are grown to st
udy the effect of broken structural inversion symmetry. We compare the perpendicular magnetic anisotropy (PMA) energy of symmetric Pt/Co/Pt, Ir/Co/Ir multilayers and asymmetric Pt/Co/Ir, Ir/Co/Pt multilayers. First, the interface contribution to the PMA is studied using the Co layer thickness dependence of the effective PMA energy. Comparison of the interfacial PMA between the Ir/Co/Pt, Pt/Co/Ir asymmetric structures and Pt/Co/Pt, Ir/Co/Ir symmetric structures indicate that the broken structural inversion symmetry induced PMA is small compared to the overall interfacial PMA. Second, we find the magnetic anisotropy field is significantly increased in multilayers when the ferromagnetic layers are antiferromagnetically coupled via interlayer exchange coupling (IEC). Macrospin model calculations can qualitatively account for the relation between the anisotropy field and the IEC. Among the structures studied, IEC is the largest for the asymmetric Ir/Co/Pt multilayers: the exchange coupling field exceeds 3 T and consequently, the anisotropy field approaches 10 T. Third, comparing the asymmetric Ir/Co/Pt and Pt/Co/Ir structures, we find the IEC and, to some extent, the interface PMA are stronger for the former than the latter. X-ray magnetic circular dichroism studies suggest that the proximity induced magnetization in Pt is larger for the Ir/Co/Pt multilayers than the inverted structure, which may partly account for the difference in the magnetic properties. These results show the intricate relation between PMA, IEC and the proximity induced magnetization that can be exploited to design artificial structures with unique magnetic characteristics.
Depth-grading of magnetic anisotropy in perpendicular magnetic media has been predicted to reduce the field required to write data without sacrificing thermal stability. To study this prediction, we have produced Co/Pd multilayers with depth-dependen
t Co layer thickness. Polarized neutron reflectometry shows that the thickness grading results in a corresponding magnetic anisotropy gradient. Magnetometry reveals that the anisotropy gradient promotes domain nucleation upon magnetization reversal - a clear experimental demonstration of the effectiveness of graded anisotropy for reducing write-field.
We investigate the correlation between roughness, remanence and coercivity in Co/Ni films grown on Cu seed layers of varying thickness. Increasing the Cu seed layer thickness of Ta/Cu/8x[Co/Ni] thin films increases the roughness of the films. In-plan
e magnetization loops show that both the remanance and coercivity increase with increasing seed layer roughness. Polar Kerr microscopy and magnetic force microscopy reveal that the domain density also increases with roughness. Finite element micromagnetic simulations performed on structures with periodically modulated surfaces provide further insight. They confirm the connection between domain density and roughness, and identify the microsocpic structure of the domain walls as the source of the increased remanence in rough films. The simulations predict that the character of the domain walls changes from Bloch-like in smooth films to Neel-like for rougher films.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
