اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدResolving ECRH deposition broadening due to edge turbulence in DIII-D by 3D full-wave simulations
72
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Edge plasma density fluctuations are shown to have a significant effect on the electron cyclotron resonance heating (ECRH) beam in the DIII-D tokamak. Experimental measurements of the ECRH deposition profile have been taken in three operating scenarios: L-mode, H-mode and negative triangularity. Each scenario corresponds to distinct turbulence characteristics in the edge region through which the beam must propagate. The measured ECRH deposition profile is significantly broadened by comparison to the profile predicted by the ray tracing code TORAY-GA and has been shown to scale with the severity of edge turbulence. Conventional ray tracing does not include the effects of turbulence and therefore a 3D full-wave cold plasma finite difference time domain code EMIT-3D is presented and used for the simulations. The turbulence is generated through the Hermes model in the BOUT++ framework which takes as input the measured time averaged electron density, temperature and magnetic field profiles for the specific shot in question. The simulated turbulence is constrained to match the experimentally measured (by use of the BES and DBS systems) correlation length and normalised fluctuation levels. The predictions of the beam broadening from the simulations are found to agree very well with the experimentally-observed broadening in all cases: L-mode, H-mode and negative triangularity. Due to the large gradients within the H-mode edge, the resolution uncertainty and error in the measurement from Thomson scattering and BES diagnostics result in a spread in the simulated turbulence amplitude. In light of this a parameter scan through the range in experimental diagnostic measurement uncertainty has been conducted to explore the impact on beam broadening predictions.
قيم البحث
اقرأ أيضاً
The physical processes taking place at the edge region are crucial for the operation of tokamaks as they govern the interaction of hot plasma with the vessel walls. Numerical modeling of the edge with state-of-the-art codes attempts to elucidate inte
ractions between neoclassical drifts, turbulence, poloidal and parallel flows that control the physical set-up of the SOL region. Here, we present post-processing analysis of simulations from the gyrokinetic code XGC1, comparing edge turbulence characteristics from a simulation of DIII-D against one of C-Mod. We find that the equilibrium $E times B$ flux across the separatrix has a similar poloidal pattern in both discharges which can be explained by magnetic drifts and trapped ion excursions. However, collisionality is noted to play a major role in that it prevents local charge accumulations from having global effects in C-Mod. In both cases, turbulent electron heat flux is higher than the ion one. This seems to be a universal characteristic of the tokamak edge. We identify turbulent frequencies and growth rates of the dominant mode in both simulations. In C-Mod, these numbers point to the presence of a drift wave. In DIII-D, linear simulations with Gene reveal a trapped electron mode. Furthermore, we present the amplitude and size distributions of the blobs from both simulations. Amplitude distributions are in qualitative agreement with experimental observations while size distributions are consistent with the fact that most blobs are not connecting to the divertor plates and suggest that they are generated by the shearing of the turbulent modes.
Turbulent dynamics in the scrape-off layer (SOL) of magnetic fusion devices is intermittent with large fluctuations in density and pressure. Therefore, a model is required that allows perturbations of similar or even larger magnitude to the time-aver
aged background value. The fluid-turbulence code GRILLIX is extended to such a global model, which consistently accounts for large variation in plasma parameters. Derived from the drift reduced Braginskii equations, the new GRILLIX model includes electromagnetic and electron-thermal dynamics, retains global parametric dependencies and the Boussinesq approximation is not applied. The penalisation technique is combined with the flux-coordinate independent (FCI) approach [F. Hariri and M. Ottaviani, Comput.Phys.Commun. 184:2419, (2013); A. Stegmeir et al., Comput.Phys.Commun. 198:139, (2016)], which allows to study realistic diverted geometries with X-point(s) and general boundary contours. We characterise results from turbulence simulations and investigate the effect of geometry by comparing simulations in circular geometry with toroidal limiter against realistic diverted geometry at otherwise comparable parameters. Turbulence is found to be intermittent with relative fluctuation levels of up to 40% showing that a global description is indeed important. At the same time via direct comparison, we find that the Boussinesq approximation has only a small quantitative impact in a turbulent environment. In comparison to circular geometry the fluctuations are reduced in diverted geometry, which is related to a different zonal flow structure. Moreover, the fluctuation level has a more complex spatial distribution in diverted geometry. Due to local magnetic shear, which differs fundamentally in circular and diverted geometry, turbulent structures become strongly distorted in the perpendicular direction and are eventually damped away towards the X-point.
Extended-MHD modeling of DIII-D tokamak [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] quiescent H-mode (QH-mode) discharges with nonlinear NIMROD [C. R. Sovinec et al., J. Comput. Phys. 195, 355 (2004)] simulations saturates into a turbulent state but d
oes not saturate when the steady-state flow inferred from measurements is not included. This is consistent with the experimental observations of the quiescent regime on DIII-D. The simulation with flow develops into a saturated turbulent state where the n=1 and 2 toroidal modes become dominant through an inverse cascade. Each mode in the range of n=1-5 is dominant at a different time. Consistent with experimental observations during QH-mode, the simulated state leads to large particle transport relative to the thermal transport. Analysis shows that the amplitude and phase of the density and temperature perturbations differ resulting in greater fluctuation-induced convective particle transport relative to the convective thermal transport. Comparison to magnetic-coil measurements shows that rotation frequencies differ between the simulation and experiment, which indicates that more sophisticated extended-MHD two-fluid modeling is required.
The free-streaming plus recycling model (FSRM) has recently been developed to understand and predict tungsten gross erosion rates from the divertor during edge localized modes (ELMs). In this work, the FSRM was tested against experimental measurement
s of W sputtering during ELMs, conducted via fast WI spectroscopy. Good agreement is observed using a variety of controlling techniques, including gas puffing, neutral beam heating, and plasma shaping to modify the pedestal stability boundary and thus the ELM behavior. ELM mitigation by pellet pacing was observed to strongly reduce W sputtering by flushing C impurities from the pedestal and reducing the divertor target electron temperature. No reduction of W sputtering was observed during the application of resonant magnetic perturbations (RMPs), in contrast to the prediction of the FSRM. Potential sources of this discrepancy are discussed. Finally, the framework of the FSRM is utilized to predict intra-ELM W sputtering rates in ITER. It is concluded that W erosion during ELMs in ITER will be caused mainly by free-streaming fuel ions, but free-streaming seeded impurities (N or Ne) may increase the erosion rate significantly if present in the pedestal at even the 1% level. Impurity recycling is not expected to cause significant W erosion in ITER due to the very low target electron temperature.
Alfven Eigenmodes and magneto-hydrodynamic modes are destabilized in DIII-D reverse magnetic shear configurations and may limit the performance of the device. We use the reduced MHD equations in a full 3D system, coupled with equations of density and
parallel velocity moments for the energetic particles (with gyro-fluid closures) as well as the geodesic acoustic wave dynamics. The aim of the study consists in finding ways to avoid or minimize MHD and AE activity for different magnetic field configurations and neutral beam injection operational regimes. The simulations show at the beginning of the discharge, before the reverse shear region is formed, a plasma that is AE unstable and marginally MHD stable. As soon as the reverse shear region appears, ideal MHD modes are destabilized with a larger growth rate than the AEs. Both MHD modes and AEs coexist during the discharge, although the MHD modes are more unstable as the reverse shear region deepens. The simulations indicate the destabilization of Beta induced AE, Toroidal AE, Elliptical AE and Reverse Shear AE at different phases of the discharges. A further analysis of the NBI operational regime indicates that the AE stability can be improved if the NBI injection is off axis, because on-axis injection leads to AEs with larger growth rate and frequency. In addition, decreasing the beam energy or increasing the NBI relative density leads to AEs with larger growth rate and frequency, so an NBI operation in the weakly resonant regime requires higher beam energies than in the experiment. The MHD linear stability can be also improved if the reverse shear region and the q profile near the magnetic axis are in between the rational surfaces q=2 and q=1, particularly if there is a region in the core with negative shear, avoiding a flat q profile near the magnetic axis.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
