اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدAvalanche boron fusion by laser picosecond block ignition with magnetic trapping for clean and economic reactor
94
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
After the very long consideration of the ideal energy source by fusion of the protons of light hydrogen with the boron isotope 11 (boron fusion HB11) the very first two independent measurements of very high reaction gains by lasers basically opens a fundamental breakthrough. The non-thermal plasma block ignition with extremely high power laser pulses above petawatt of picosecond duration in combination with up to ten kilotesla magnetic fields for trapping has to be combined to use the measured high gains as proof of an avalanche reaction for an environmentally clean, low cost and lasting energy source as potential option against global warming. The unique HB11 avalanche reaction is are now based on elastic collisions of helium nuclei (alpha particles) limited only to a reactor for controlled fusion energy during a very short time within a very small volume.
قيم البحث
اقرأ أيضاً
To enhance the core heating efficiency in fast ignition laser fusion, the concept of relativistic electron beam guiding by external magnetic fields was evaluated by integrated simulations for FIREX class targets. For the cone-attached shell target ca
se, the core heating performance is deteriorated by applying magnetic fields since the core is considerably deformed and the most of the fast electrons are reflected due to the magnetic mirror formed through the implosion. On the other hand, in the case of cone-attached solid ball target, the implosion is more stable under the kilo-tesla-class magnetic field. In addition, feasible magnetic field configuration is formed through the implosion. As the results, the core heating efficiency becomes double by magnetic guiding. The dependence of core heating properties on the heating pulse shot timing was also investigated for the solid ball target.
In the electron-driven fast-ignition approach to inertial confinement fusion, petawatt laser pulses are required to generate MeV electrons that deposit several tens of kilojoules in the compressed core of an imploded DT shell. We review recent progre
ss in the understanding of intense laser plasma interactions (LPI) relevant to fast ignition. Increases in computational and modeling capabilities, as well as algorithmic developments have led to enhancement in our ability to perform multi-dimensional particle-in-cell (PIC) simulations of LPI at relevant scales. We discuss the physics of the interaction in terms of laser absorption fraction, the laser-generated electron spectra, divergence, and their temporal evolution. Scaling with irradiation conditions such as laser intensity are considered, as well as the dependence on plasma parameters. Different numerical modeling approaches and configurations are addressed, providing an overview of the modeling capabilities and limitations. In addition, we discuss the comparison of simulation results with experimental observables. In particular, we address the question of surrogacy of todays experiments for the full-scale fast ignition problem.
A feasibility study of fusion reactors based on accelerators is carried out. We consider a novel scheme where a beam from the accelerator hits the target plasma on the resonance of the fusion reaction and establish characteristic criteria for a worka
ble reactor. We consider the reactions $ d + t rightarrow n + alpha, d + {}^3H_e rightarrow p + alpha$, and $p + {}^{11}B rightarrow 3 alpha$ in this study. The critical temperature of the plasma is determined from overcoming the stopping power of the beam with the fusion energy gain. The needed plasma lifetime is determined from the width of the resonance, the beam velocity and the plasma density. We estimate the critical beam flux by balancing the energy of fusion production against the plasma thermo-energy and the loss due to stopping power for the case of an inert plasma. The product of critical flux and plasma lifetime is independent of plasma density and has a weak dependence on temperature. Even though the critical temperatures for these reactions are lower than those for the thermonuclear reactors, the critical flux is in the range of $10^{22} - 10^{24}/rm{cm^2/s}$ for the plasma density $rho_t = 10^{15}/{rm cm^3}$ in the case of an inert plasma. Several approaches to control the growth of the two-stream instability are discussed. We have also considered several scenarios for practical implementation which will require further studies. Finally, we consider the case where the injected beam at the resonance energy maintains the plasma temperature and prolongs its lifetime to reach a steady state. The equations for power balance and particle number conservation are given for this case.
We revisit the assumption that reactors based on deuterium-deuterium (D-D) fusion processes have to be necessarily developed after the successful completion of experiments and demonstrations for deuterium-tritium (D-T) fusion reactors. Two possible m
echanisms for enhancing the reactivity are discussed. Hard tails in the energy distribution of the nuclei, through the so-called kappa-distribution, allow to boost the number of energetic nuclei available for fusion reactions. At higher temperatures than usually considered in D-T plasmas, vacuum polarization effects from real $e^+e^-$ and $mu^+mu^-$ pairs may provide further speed-up due to their contribution to screening of the Coulomb barrier. Furthermore, the energy collection system can benefit from the absence of the lithium blanket, both in simplicity and compactness. The usual thermal cycle can be bypassed with comparable efficiency levels using hadronic calorimetry and third-generation photovoltaic cells, possibly allowing to extend the use of fusion reactors to broader contexts, most notably maritime transport.
The document describes a numerical algorithm to simulate plasmas and fluids in the 3 dimensional space by the Euler method, in which the spatial meshes are fixed to the space. The plasmas and fluids move through the spacial Euler mesh boundary. The E
uler method can represent a large deformation of the plasmas and fluids. On the other hand, when the plasmas or fluids are compressed to a high density, the spatial resolution should be ensured to describe the density change precisely. The present 3D Euler code is developed to simulate a nuclear fusion fuel ignition and burning. Therefore, the 3D Euler code includes the DT fuel reactions, the alpha particle diffusion, the alpha particle deposition to heat the DT fuel and the DT fuel depletion by the DT reactions, as well as the thermal energy diffusion based on the three-temperature compressible fluid model.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
